9 #error Wrong include order: MAVLINK_COMMON.H MUST NOT BE DIRECTLY USED. Include mavlink.h from the same directory instead or set ALL AND EVERY defines from MAVLINK.H manually accordingly, including the #define MAVLINK_H call.
121MAV_MODE_FLAG_TEST_ENABLED=2, /* 0b00000010 system has a test mode enabled. This flag is intended for temporary system tests and should not be used for stable implementations. | */
122MAV_MODE_FLAG_AUTO_ENABLED=4, /* 0b00000100 autonomous mode enabled, system finds its own goal positions. Guided flag can be set or not, depends on the actual implementation. | */
124MAV_MODE_FLAG_STABILIZE_ENABLED=16, /* 0b00010000 system stabilizes electronically its attitude (and optionally position). It needs however further control inputs to move around. | */
125MAV_MODE_FLAG_HIL_ENABLED=32, /* 0b00100000 hardware in the loop simulation. All motors / actuators are blocked, but internal software is full operational. | */
172MAV_MODE_GUIDED_DISARMED=88, /* System is allowed to be active, under autonomous control, manual setpoint | */
173MAV_MODE_AUTO_DISARMED=92, /* System is allowed to be active, under autonomous control and navigation (the trajectory is decided onboard and not pre-programmed by MISSIONs) | */
174MAV_MODE_MANUAL_ARMED=192, /* System is allowed to be active, under manual (RC) control, no stabilization | */
175MAV_MODE_TEST_ARMED=194, /* UNDEFINED mode. This solely depends on the autopilot - use with caution, intended for developers only. | */
177MAV_MODE_GUIDED_ARMED=216, /* System is allowed to be active, under autonomous control, manual setpoint | */
178MAV_MODE_AUTO_ARMED=220, /* System is allowed to be active, under autonomous control and navigation (the trajectory is decided onboard and not pre-programmed by MISSIONs) | */
191MAV_STATE_STANDBY=3, /* System is grounded and on standby. It can be launched any time. | */
192MAV_STATE_ACTIVE=4, /* System is active and might be already airborne. Motors are engaged. | */
193MAV_STATE_CRITICAL=5, /* System is in a non-normal flight mode. It can however still navigate. | */
194MAV_STATE_EMERGENCY=6, /* System is in a non-normal flight mode. It lost control over parts or over the whole airframe. It is in mayday and going down. | */
195MAV_STATE_POWEROFF=7, /* System just initialized its power-down sequence, will shut down now. | */
278MAV_FRAME_GLOBAL=0, /* Global coordinate frame, WGS84 coordinate system. First value / x: latitude, second value / y: longitude, third value / z: positive altitude over mean sea level (MSL) | */
280MAV_FRAME_MISSION=2, /* NOT a coordinate frame, indicates a mission command. | */
281MAV_FRAME_GLOBAL_RELATIVE_ALT=3, /* Global coordinate frame, WGS84 coordinate system, relative altitude over ground with respect to the home position. First value / x: latitude, second value / y: longitude, third value / z: positive altitude with 0 being at the altitude of the home location. | */
283MAV_FRAME_GLOBAL_INT=5, /* Global coordinate frame, WGS84 coordinate system. First value / x: latitude in degrees*1.0e-7, second value / y: longitude in degrees*1.0e-7, third value / z: positive altitude over mean sea level (MSL) | */
284MAV_FRAME_GLOBAL_RELATIVE_ALT_INT=6, /* Global coordinate frame, WGS84 coordinate system, relative altitude over ground with respect to the home position. First value / x: latitude in degrees*10e-7, second value / y: longitude in degrees*10e-7, third value / z: positive altitude with 0 being at the altitude of the home location. | */
285MAV_FRAME_LOCAL_OFFSET_NED=7, /* Offset to the current local frame. Anything expressed in this frame should be added to the current local frame position. | */
286MAV_FRAME_BODY_NED=8, /* Setpoint in body NED frame. This makes sense if all position control is externalized - e.g. useful to command 2 m/s^2 acceleration to the right. | */
287MAV_FRAME_BODY_OFFSET_NED=9, /* Offset in body NED frame. This makes sense if adding setpoints to the current flight path, to avoid an obstacle - e.g. useful to command 2 m/s^2 acceleration to the east. | */
288MAV_FRAME_GLOBAL_TERRAIN_ALT=10, /* Global coordinate frame with above terrain level altitude. WGS84 coordinate system, relative altitude over terrain with respect to the waypoint coordinate. First value / x: latitude in degrees, second value / y: longitude in degrees, third value / z: positive altitude in meters with 0 being at ground level in terrain model. | */
289MAV_FRAME_GLOBAL_TERRAIN_ALT_INT=11, /* Global coordinate frame with above terrain level altitude. WGS84 coordinate system, relative altitude over terrain with respect to the waypoint coordinate. First value / x: latitude in degrees*10e-7, second value / y: longitude in degrees*10e-7, third value / z: positive altitude in meters with 0 being at ground level in terrain model. | */
354MAV_CMD_NAV_WAYPOINT=16, /* Navigate to MISSION. |Hold time in decimal seconds. (ignored by fixed wing, time to stay at MISSION for rotary wing)| Acceptance radius in meters (if the sphere with this radius is hit, the MISSION counts as reached)| 0 to pass through the WP, if > 0 radius in meters to pass by WP. Positive value for clockwise orbit, negative value for counter-clockwise orbit. Allows trajectory control.| Desired yaw angle at MISSION (rotary wing)| Latitude| Longitude| Altitude| */
355MAV_CMD_NAV_LOITER_UNLIM=17, /* Loiter around this MISSION an unlimited amount of time |Empty| Empty| Radius around MISSION, in meters. If positive loiter clockwise, else counter-clockwise| Desired yaw angle.| Latitude| Longitude| Altitude| */
356MAV_CMD_NAV_LOITER_TURNS=18, /* Loiter around this MISSION for X turns |Turns| Empty| Radius around MISSION, in meters. If positive loiter clockwise, else counter-clockwise| Forward moving aircraft this sets exit xtrack location: 0 for center of loiter wp, 1 for exit location. Else, this is desired yaw angle| Latitude| Longitude| Altitude| */
357MAV_CMD_NAV_LOITER_TIME=19, /* Loiter around this MISSION for X seconds |Seconds (decimal)| Empty| Radius around MISSION, in meters. If positive loiter clockwise, else counter-clockwise| Forward moving aircraft this sets exit xtrack location: 0 for center of loiter wp, 1 for exit location. Else, this is desired yaw angle| Latitude| Longitude| Altitude| */
359MAV_CMD_NAV_LAND=21, /* Land at location |Abort Alt| Empty| Empty| Desired yaw angle| Latitude| Longitude| Altitude| */
360MAV_CMD_NAV_TAKEOFF=22, /* Takeoff from ground / hand |Minimum pitch (if airspeed sensor present), desired pitch without sensor| Empty| Empty| Yaw angle (if magnetometer present), ignored without magnetometer| Latitude| Longitude| Altitude| */
361MAV_CMD_NAV_LAND_LOCAL=23, /* Land at local position (local frame only) |Landing target number (if available)| Maximum accepted offset from desired landing position [m] - computed magnitude from spherical coordinates: d = sqrt(x^2 + y^2 + z^2), which gives the maximum accepted distance between the desired landing position and the position where the vehicle is about to land| Landing descend rate [ms^-1]| Desired yaw angle [rad]| Y-axis position [m]| X-axis position [m]| Z-axis / ground level position [m]| */
362MAV_CMD_NAV_TAKEOFF_LOCAL=24, /* Takeoff from local position (local frame only) |Minimum pitch (if airspeed sensor present), desired pitch without sensor [rad]| Empty| Takeoff ascend rate [ms^-1]| Yaw angle [rad] (if magnetometer or another yaw estimation source present), ignored without one of these| Y-axis position [m]| X-axis position [m]| Z-axis position [m]| */
363MAV_CMD_NAV_FOLLOW=25, /* Vehicle following, i.e. this waypoint represents the position of a moving vehicle |Following logic to use (e.g. loitering or sinusoidal following) - depends on specific autopilot implementation| Ground speed of vehicle to be followed| Radius around MISSION, in meters. If positive loiter clockwise, else counter-clockwise| Desired yaw angle.| Latitude| Longitude| Altitude| */
364MAV_CMD_NAV_CONTINUE_AND_CHANGE_ALT=30, /* Continue on the current course and climb/descend to specified altitude. When the altitude is reached continue to the next command (i.e., don't proceed to the next command until the desired altitude is reached. |Climb or Descend (0 = Neutral, command completes when within 5m of this command's altitude, 1 = Climbing, command completes when at or above this command's altitude, 2 = Descending, command completes when at or below this command's altitude. | Empty| Empty| Empty| Empty| Empty| Desired altitude in meters| */
365MAV_CMD_NAV_LOITER_TO_ALT=31, /* Begin loiter at the specified Latitude and Longitude. If Lat=Lon=0, then loiter at the current position. Don't consider the navigation command complete (don't leave loiter) until the altitude has been reached. Additionally, if the Heading Required parameter is non-zero the aircraft will not leave the loiter until heading toward the next waypoint. |Heading Required (0 = False)| Radius in meters. If positive loiter clockwise, negative counter-clockwise, 0 means no change to standard loiter.| Empty| Forward moving aircraft this sets exit xtrack location: 0 for center of loiter wp, 1 for exit location| Latitude| Longitude| Altitude| */
366MAV_CMD_DO_FOLLOW=32, /* Being following a target |System ID (the system ID of the FOLLOW_TARGET beacon). Send 0 to disable follow-me and return to the default position hold mode| RESERVED| RESERVED| altitude flag: 0: Keep current altitude, 1: keep altitude difference to target, 2: go to a fixed altitude above home| altitude| RESERVED| TTL in seconds in which the MAV should go to the default position hold mode after a message rx timeout| */
367MAV_CMD_DO_FOLLOW_REPOSITION=33, /* Reposition the MAV after a follow target command has been sent |Camera q1 (where 0 is on the ray from the camera to the tracking device)| Camera q2| Camera q3| Camera q4| altitude offset from target (m)| X offset from target (m)| Y offset from target (m)| */
368MAV_CMD_NAV_ROI=80, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of intereset mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z| */
369MAV_CMD_NAV_PATHPLANNING=81, /* Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning| 0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid| Empty| Yaw angle at goal, in compass degrees, [0..360]| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal| */
370MAV_CMD_NAV_SPLINE_WAYPOINT=82, /* Navigate to MISSION using a spline path. |Hold time in decimal seconds. (ignored by fixed wing, time to stay at MISSION for rotary wing)| Empty| Empty| Empty| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal| */
371MAV_CMD_NAV_VTOL_TAKEOFF=84, /* Takeoff from ground using VTOL mode |Empty| Empty| Empty| Yaw angle in degrees| Latitude| Longitude| Altitude| */
372MAV_CMD_NAV_VTOL_LAND=85, /* Land using VTOL mode |Empty| Empty| Empty| Yaw angle in degrees| Latitude| Longitude| Altitude| */
373MAV_CMD_NAV_GUIDED_ENABLE=92, /* hand control over to an external controller |On / Off (> 0.5f on)| Empty| Empty| Empty| Empty| Empty| Empty| */
374MAV_CMD_NAV_DELAY=93, /* Delay the next navigation command a number of seconds or until a specified time |Delay in seconds (decimal, -1 to enable time-of-day fields)| hour (24h format, UTC, -1 to ignore)| minute (24h format, UTC, -1 to ignore)| second (24h format, UTC)| Empty| Empty| Empty| */
375MAV_CMD_NAV_LAST=95, /* NOP - This command is only used to mark the upper limit of the NAV/ACTION commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty| */
376MAV_CMD_CONDITION_DELAY=112, /* Delay mission state machine. |Delay in seconds (decimal)| Empty| Empty| Empty| Empty| Empty| Empty| */
377MAV_CMD_CONDITION_CHANGE_ALT=113, /* Ascend/descend at rate. Delay mission state machine until desired altitude reached. |Descent / Ascend rate (m/s)| Empty| Empty| Empty| Empty| Empty| Finish Altitude| */
378MAV_CMD_CONDITION_DISTANCE=114, /* Delay mission state machine until within desired distance of next NAV point. |Distance (meters)| Empty| Empty| Empty| Empty| Empty| Empty| */
379MAV_CMD_CONDITION_YAW=115, /* Reach a certain target angle. |target angle: [0-360], 0 is north| speed during yaw change:[deg per second]| direction: negative: counter clockwise, positive: clockwise [-1,1]| relative offset or absolute angle: [ 1,0]| Empty| Empty| Empty| */
380MAV_CMD_CONDITION_LAST=159, /* NOP - This command is only used to mark the upper limit of the CONDITION commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty| */
381MAV_CMD_DO_SET_MODE=176, /* Set system mode. |Mode, as defined by ENUM MAV_MODE| Custom mode - this is system specific, please refer to the individual autopilot specifications for details.| Custom sub mode - this is system specific, please refer to the individual autopilot specifications for details.| Empty| Empty| Empty| Empty| */
382MAV_CMD_DO_JUMP=177, /* Jump to the desired command in the mission list. Repeat this action only the specified number of times |Sequence number| Repeat count| Empty| Empty| Empty| Empty| Empty| */
383MAV_CMD_DO_CHANGE_SPEED=178, /* Change speed and/or throttle set points. |Speed type (0=Airspeed, 1=Ground Speed)| Speed (m/s, -1 indicates no change)| Throttle ( Percent, -1 indicates no change)| absolute or relative [0,1]| Empty| Empty| Empty| */
384MAV_CMD_DO_SET_HOME=179, /* Changes the home location either to the current location or a specified location. |Use current (1=use current location, 0=use specified location)| Empty| Empty| Empty| Latitude| Longitude| Altitude| */
385MAV_CMD_DO_SET_PARAMETER=180, /* Set a system parameter. Caution! Use of this command requires knowledge of the numeric enumeration value of the parameter. |Parameter number| Parameter value| Empty| Empty| Empty| Empty| Empty| */
386MAV_CMD_DO_SET_RELAY=181, /* Set a relay to a condition. |Relay number| Setting (1=on, 0=off, others possible depending on system hardware)| Empty| Empty| Empty| Empty| Empty| */
387MAV_CMD_DO_REPEAT_RELAY=182, /* Cycle a relay on and off for a desired number of cyles with a desired period. |Relay number| Cycle count| Cycle time (seconds, decimal)| Empty| Empty| Empty| Empty| */
388MAV_CMD_DO_SET_SERVO=183, /* Set a servo to a desired PWM value. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Empty| Empty| Empty| Empty| Empty| */
389MAV_CMD_DO_REPEAT_SERVO=184, /* Cycle a between its nominal setting and a desired PWM for a desired number of cycles with a desired period. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Cycle count| Cycle time (seconds)| Empty| Empty| Empty| */
391MAV_CMD_DO_LAND_START=189, /* Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty| */
392MAV_CMD_DO_RALLY_LAND=190, /* Mission command to perform a landing from a rally point. |Break altitude (meters)| Landing speed (m/s)| Empty| Empty| Empty| Empty| Empty| */
393MAV_CMD_DO_GO_AROUND=191, /* Mission command to safely abort an autonmous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty| */
394MAV_CMD_DO_REPOSITION=192, /* Reposition the vehicle to a specific WGS84 global position. |Ground speed, less than 0 (-1) for default| Bitmask of option flags, see the MAV_DO_REPOSITION_FLAGS enum.| Reserved| Yaw heading, NaN for unchanged. For planes indicates loiter direction (0: clockwise, 1: counter clockwise)| Latitude (deg * 1E7)| Longitude (deg * 1E7)| Altitude (meters)| */
395MAV_CMD_DO_PAUSE_CONTINUE=193, /* If in a GPS controlled position mode, hold the current position or continue. |0: Pause current mission or reposition command, hold current position. 1: Continue mission. A VTOL capable vehicle should enter hover mode (multicopter and VTOL planes). A plane should loiter with the default loiter radius.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved| */
396MAV_CMD_DO_CONTROL_VIDEO=200, /* Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty| */
397MAV_CMD_DO_SET_ROI=201, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of intereset mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z| */
398MAV_CMD_DO_DIGICAM_CONFIGURE=202, /* Mission command to configure an on-board camera controller system. |Modes: P, TV, AV, M, Etc| Shutter speed: Divisor number for one second| Aperture: F stop number| ISO number e.g. 80, 100, 200, Etc| Exposure type enumerator| Command Identity| Main engine cut-off time before camera trigger in seconds/10 (0 means no cut-off)| */
399MAV_CMD_DO_DIGICAM_CONTROL=203, /* Mission command to control an on-board camera controller system. |Session control e.g. show/hide lens| Zoom's absolute position| Zooming step value to offset zoom from the current position| Focus Locking, Unlocking or Re-locking| Shooting Command| Command Identity| Empty| */
400MAV_CMD_DO_MOUNT_CONFIGURE=204, /* Mission command to configure a camera or antenna mount |Mount operation mode (see MAV_MOUNT_MODE enum)| stabilize roll? (1 = yes, 0 = no)| stabilize pitch? (1 = yes, 0 = no)| stabilize yaw? (1 = yes, 0 = no)| Empty| Empty| Empty| */
401MAV_CMD_DO_MOUNT_CONTROL=205, /* Mission command to control a camera or antenna mount |pitch or lat in degrees, depending on mount mode.| roll or lon in degrees depending on mount mode| yaw or alt (in meters) depending on mount mode| reserved| reserved| reserved| MAV_MOUNT_MODE enum value| */
402MAV_CMD_DO_SET_CAM_TRIGG_DIST=206, /* Mission command to set CAM_TRIGG_DIST for this flight |Camera trigger distance (meters)| Empty| Empty| Empty| Empty| Empty| Empty| */
403MAV_CMD_DO_FENCE_ENABLE=207, /* Mission command to enable the geofence |enable? (0=disable, 1=enable, 2=disable_floor_only)| Empty| Empty| Empty| Empty| Empty| Empty| */
404MAV_CMD_DO_PARACHUTE=208, /* Mission command to trigger a parachute |action (0=disable, 1=enable, 2=release, for some systems see PARACHUTE_ACTION enum, not in general message set.)| Empty| Empty| Empty| Empty| Empty| Empty| */
406MAV_CMD_DO_MOUNT_CONTROL_QUAT=220, /* Mission command to control a camera or antenna mount, using a quaternion as reference. |q1 - quaternion param #1, w (1 in null-rotation)| q2 - quaternion param #2, x (0 in null-rotation)| q3 - quaternion param #3, y (0 in null-rotation)| q4 - quaternion param #4, z (0 in null-rotation)| Empty| Empty| Empty| */
407MAV_CMD_DO_GUIDED_MASTER=221, /* set id of master controller |System ID| Component ID| Empty| Empty| Empty| Empty| Empty| */
408MAV_CMD_DO_GUIDED_LIMITS=222, /* set limits for external control |timeout - maximum time (in seconds) that external controller will be allowed to control vehicle. 0 means no timeout| absolute altitude min (in meters, AMSL) - if vehicle moves below this alt, the command will be aborted and the mission will continue. 0 means no lower altitude limit| absolute altitude max (in meters)- if vehicle moves above this alt, the command will be aborted and the mission will continue. 0 means no upper altitude limit| horizontal move limit (in meters, AMSL) - if vehicle moves more than this distance from it's location at the moment the command was executed, the command will be aborted and the mission will continue. 0 means no horizontal altitude limit| Empty| Empty| Empty| */
409MAV_CMD_DO_LAST=240, /* NOP - This command is only used to mark the upper limit of the DO commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty| */
410MAV_CMD_PREFLIGHT_CALIBRATION=241, /* Trigger calibration. This command will be only accepted if in pre-flight mode. |Gyro calibration: 0: no, 1: yes| Magnetometer calibration: 0: no, 1: yes| Ground pressure: 0: no, 1: yes| Radio calibration: 0: no, 1: yes| Accelerometer calibration: 0: no, 1: yes| Compass/Motor interference calibration: 0: no, 1: yes| Empty| */
411MAV_CMD_PREFLIGHT_SET_SENSOR_OFFSETS=242, /* Set sensor offsets. This command will be only accepted if in pre-flight mode. |Sensor to adjust the offsets for: 0: gyros, 1: accelerometer, 2: magnetometer, 3: barometer, 4: optical flow, 5: second magnetometer| X axis offset (or generic dimension 1), in the sensor's raw units| Y axis offset (or generic dimension 2), in the sensor's raw units| Z axis offset (or generic dimension 3), in the sensor's raw units| Generic dimension 4, in the sensor's raw units| Generic dimension 5, in the sensor's raw units| Generic dimension 6, in the sensor's raw units| */
412MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN config. This command will be only accepted if in pre-flight mode. |1: Trigger actuator ID assignment and direction mapping.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved| */
413MAV_CMD_PREFLIGHT_STORAGE=245, /* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Onboard logging: 0: Ignore, 1: Start default rate logging, -1: Stop logging, > 1: start logging with rate of param 3 in Hz (e.g. set to 1000 for 1000 Hz logging)| Reserved| Empty| Empty| Empty| */
414MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN=246, /* Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot, 3: Reboot autopilot and keep it in the bootloader until upgraded.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer, 3: Reboot onboard computer and keep it in the bootloader until upgraded.| Reserved, send 0| Reserved, send 0| Reserved, send 0| Reserved, send 0| Reserved, send 0| */
415MAV_CMD_OVERRIDE_GOTO=252, /* Hold / continue the current action |MAV_GOTO_DO_HOLD: hold MAV_GOTO_DO_CONTINUE: continue with next item in mission plan| MAV_GOTO_HOLD_AT_CURRENT_POSITION: Hold at current position MAV_GOTO_HOLD_AT_SPECIFIED_POSITION: hold at specified position| MAV_FRAME coordinate frame of hold point| Desired yaw angle in degrees| Latitude / X position| Longitude / Y position| Altitude / Z position| */
416MAV_CMD_MISSION_START=300, /* start running a mission |first_item: the first mission item to run| last_item: the last mission item to run (after this item is run, the mission ends)| */
418MAV_CMD_GET_HOME_POSITION=410, /* Request the home position from the vehicle. |Reserved| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved| */
420MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID |The MAVLink message ID| */
421MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Request the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM |The MAVLink message ID| The interval between two messages, in microseconds. Set to -1 to disable and 0 to request default rate.| */
423MAV_CMD_IMAGE_START_CAPTURE=2000, /* Start image capture sequence |Duration between two consecutive pictures (in seconds)| Number of images to capture total - 0 for unlimited capture| Resolution in megapixels (0.3 for 640x480, 1.3 for 1280x720, etc)| */
425MAV_CMD_DO_TRIGGER_CONTROL=2003, /* Enable or disable on-board camera triggering system. |Trigger enable/disable (0 for disable, 1 for start)| Shutter integration time (in ms)| Reserved| */
426MAV_CMD_VIDEO_START_CAPTURE=2500, /* Starts video capture |Camera ID (0 for all cameras), 1 for first, 2 for second, etc.| Frames per second| Resolution in megapixels (0.3 for 640x480, 1.3 for 1280x720, etc)| */
428MAV_CMD_PANORAMA_CREATE=2800, /* Create a panorama at the current position |Viewing angle horizontal of the panorama (in degrees, +- 0.5 the total angle)| Viewing angle vertical of panorama (in degrees)| Speed of the horizontal rotation (in degrees per second)| Speed of the vertical rotation (in degrees per second)| */
429MAV_CMD_DO_VTOL_TRANSITION=3000, /* Request VTOL transition |The target VTOL state, as defined by ENUM MAV_VTOL_STATE. Only MAV_VTOL_STATE_MC and MAV_VTOL_STATE_FW can be used.| */
430MAV_CMD_PAYLOAD_PREPARE_DEPLOY=30001, /* Deploy payload on a Lat / Lon / Alt position. This includes the navigation to reach the required release position and velocity. |Operation mode. 0: prepare single payload deploy (overwriting previous requests), but do not execute it. 1: execute payload deploy immediately (rejecting further deploy commands during execution, but allowing abort). 2: add payload deploy to existing deployment list.| Desired approach vector in degrees compass heading (0..360). A negative value indicates the system can define the approach vector at will.| Desired ground speed at release time. This can be overriden by the airframe in case it needs to meet minimum airspeed. A negative value indicates the system can define the ground speed at will.| Minimum altitude clearance to the release position in meters. A negative value indicates the system can define the clearance at will.| Latitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Longitude unscaled for MISSION_ITEM or in 1e7 degrees for MISSION_ITEM_INT| Altitude, in meters AMSL| */
431MAV_CMD_PAYLOAD_CONTROL_DEPLOY=30002, /* Control the payload deployment. |Operation mode. 0: Abort deployment, continue normal mission. 1: switch to payload deploment mode. 100: delete first payload deployment request. 101: delete all payload deployment requests.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved| */
432MAV_CMD_WAYPOINT_USER_1=31000, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude, in meters AMSL| */
433MAV_CMD_WAYPOINT_USER_2=31001, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude, in meters AMSL| */
434MAV_CMD_WAYPOINT_USER_3=31002, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude, in meters AMSL| */
435MAV_CMD_WAYPOINT_USER_4=31003, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude, in meters AMSL| */
436MAV_CMD_WAYPOINT_USER_5=31004, /* User defined waypoint item. Ground Station will show the Vehicle as flying through this item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude, in meters AMSL| */
437MAV_CMD_SPATIAL_USER_1=31005, /* User defined spatial item. Ground Station will not show the Vehicle as flying through this item. Example: ROI item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude, in meters AMSL| */
438MAV_CMD_SPATIAL_USER_2=31006, /* User defined spatial item. Ground Station will not show the Vehicle as flying through this item. Example: ROI item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude, in meters AMSL| */
439MAV_CMD_SPATIAL_USER_3=31007, /* User defined spatial item. Ground Station will not show the Vehicle as flying through this item. Example: ROI item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude, in meters AMSL| */
440MAV_CMD_SPATIAL_USER_4=31008, /* User defined spatial item. Ground Station will not show the Vehicle as flying through this item. Example: ROI item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude, in meters AMSL| */
441MAV_CMD_SPATIAL_USER_5=31009, /* User defined spatial item. Ground Station will not show the Vehicle as flying through this item. Example: ROI item. |User defined| User defined| User defined| User defined| Latitude unscaled| Longitude unscaled| Altitude, in meters AMSL| */
442MAV_CMD_USER_1=31010, /* User defined command. Ground Station will not show the Vehicle as flying through this item. Example: MAV_CMD_DO_SET_PARAMETER item. |User defined| User defined| User defined| User defined| User defined| User defined| User defined| */
443MAV_CMD_USER_2=31011, /* User defined command. Ground Station will not show the Vehicle as flying through this item. Example: MAV_CMD_DO_SET_PARAMETER item. |User defined| User defined| User defined| User defined| User defined| User defined| User defined| */
444MAV_CMD_USER_3=31012, /* User defined command. Ground Station will not show the Vehicle as flying through this item. Example: MAV_CMD_DO_SET_PARAMETER item. |User defined| User defined| User defined| User defined| User defined| User defined| User defined| */
445MAV_CMD_USER_4=31013, /* User defined command. Ground Station will not show the Vehicle as flying through this item. Example: MAV_CMD_DO_SET_PARAMETER item. |User defined| User defined| User defined| User defined| User defined| User defined| User defined| */
446MAV_CMD_USER_5=31014, /* User defined command. Ground Station will not show the Vehicle as flying through this item. Example: MAV_CMD_DO_SET_PARAMETER item. |User defined| User defined| User defined| User defined| User defined| User defined| User defined| */
497MAV_CMD_ACK_ERR_COORDINATES_OUT_OF_RANGE=6, /* The coordinate frame of this command is ok, but he coordinate values exceed the safety limits of this system. This is a generic error, please use the more specific error messages below if possible. | */
571MAV_SEVERITY_WARNING=4, /* Indicates about a possible future error if this is not resolved within a given timeframe. Example would be a low battery warning. | */
572MAV_SEVERITY_NOTICE=5, /* An unusual event has occured, though not an error condition. This should be investigated for the root cause. | */
573MAV_SEVERITY_INFO=6, /* Normal operational messages. Useful for logging. No action is required for these messages. | */
574MAV_SEVERITY_DEBUG=7, /* Useful non-operational messages that can assist in debugging. These should not occur during normal operation. | */
614SERIAL_CONTROL_FLAG_RESPOND=2, /* Set if the sender wants the receiver to send a response as another SERIAL_CONTROL message | */
615SERIAL_CONTROL_FLAG_EXCLUSIVE=4, /* Set if access to the serial port should be removed from whatever driver is currently using it, giving exclusive access to the SERIAL_CONTROL protocol. The port can be handed back by sending a request without this flag set | */
850ESTIMATOR_CONST_POS_MODE=128, /* True if the EKF is in a constant position mode and is not using external measurements (eg GPS or optical flow) | */
851ESTIMATOR_PRED_POS_HORIZ_REL=256, /* True if the EKF has sufficient data to enter a mode that will provide a (relative) position estimate | */
852ESTIMATOR_PRED_POS_HORIZ_ABS=512, /* True if the EKF has sufficient data to enter a mode that will provide a (absolute) position estimate | */