|
enum | adaptor_board_command : uint32_t {
adaptor_board_command::IRB = 0x01,
adaptor_board_command::IWB = 0x02,
adaptor_board_command::GVD = 0x03,
adaptor_board_command::IAP_IRB = 0x04,
adaptor_board_command::IAP_IWB = 0x05,
adaptor_board_command::FRCNT = 0x06,
adaptor_board_command::GLD = 0x07,
adaptor_board_command::GPW = 0x08,
adaptor_board_command::GPR = 0x09,
adaptor_board_command::MMPWR = 0x0A,
adaptor_board_command::DSPWR = 0x0B,
adaptor_board_command::EXT_TRIG = 0x0C,
adaptor_board_command::CX3FWUPD = 0x0D,
adaptor_board_command::MM_SNB = 0x10,
adaptor_board_command::MM_TRB = 0x11,
adaptor_board_command::MM_ACTIVATE = 0x0E
} |
|
enum | i2c_register : uint32_t {
i2c_register::REG_UCTRL_CFG = 0x00,
i2c_register::REG_INT_ID_CONFIG = 0x04,
i2c_register::REG_INT_TYPE_CONFIG = 0x08,
i2c_register::REG_EEPROM_CMD = 0x0C,
i2c_register::REG_EEPROM_DATA = 0xD0,
i2c_register::REG_TIMER_PRESCALER = 0x14,
i2c_register::REG_TIMER_RESET_VALUE = 0x18,
i2c_register::REG_GYRO_BYPASS_CMD1 = 0x1C,
i2c_register::REG_GYRO_BYPASS_CMD2 = 0x20,
i2c_register::REG_GYRO_BYPASS_RDOUT1 = 0x24,
i2c_register::REG_GYRO_BYPASS_RDOUT2 = 0x28,
i2c_register::REG_ACC_BYPASS_CMD1 = 0x2C,
i2c_register::REG_ACC_BYPASS_CMD2 = 0x30,
i2c_register::REG_ACC_BYPASS_RDOUT1 = 0x34,
i2c_register::REG_ACC_BYPASS_RDOUT2 = 0x38,
i2c_register::REG_REQ_LTR = 0x3C,
i2c_register::REG_STATUS_REG = 0x40,
i2c_register::REG_FIFO_RD = 0x44,
i2c_register::REG_FIRST_INT_IGNORE = 0x48,
i2c_register::REG_IAP_REG = 0x4C,
i2c_register::REG_INT_ENABLE = 0x50,
i2c_register::REG_CURR_PWR_STATE = 0x54,
i2c_register::REG_NEXT_PWR_STATE = 0x58,
i2c_register::REG_ACC_BW = 0x5C,
i2c_register::REG_GYRO_BW = 0x60,
i2c_register::REG_ACC_RANGE = 0x64,
i2c_register::REG_GYRO_RANGE = 0x68,
i2c_register::REG_IMG_VER = 0x6C,
i2c_register::REG_ERROR = 0x70,
i2c_register::REG_JUMP_TO_APP = 0x77
} |
|
enum | mm_accel_bandwidth : uint8_t { mm_accel_bandwidth::accel_bw_default = 0,
mm_accel_bandwidth::accel_bw_125hz = 1,
mm_accel_bandwidth::accel_bw_250hz = 2
} |
|
enum | mm_accel_range : uint8_t { mm_accel_range::accel_range_default = 0,
mm_accel_range::accel_range_4g = 1,
mm_accel_range::accel_range_8g = 2,
mm_accel_range::accel_range_16g = 3
} |
|
enum | mm_gyro_bandwidth : uint8_t { mm_gyro_bandwidth::gyro_bw_default = 0,
mm_gyro_bandwidth::gyro_bw_200hz = 1
} |
|
enum | mm_gyro_range : uint8_t { mm_gyro_range::gyro_range_default = 0,
mm_gyro_range::gyro_range_1000 = 1,
mm_gyro_range::gyro_range_2000 = 2
} |
|
enum | mm_request : uint8_t { mm_output_undefined = 0,
mm_video_output = 1,
mm_events_output = 2
} |
|
enum | mm_state : uint8_t { mm_idle = 0,
mm_streaming = 1,
mm_eventing = 2,
mm_full_load = 3
} |
|
enum | motion_module_errors {
imu_not_responding = 0,
illegal_configuration = 1,
ts_fifo_overflow = 2,
imu_fifo_overflow = 3,
watchdog_reset = 4,
crc_error = 5,
missing_data_from_imu = 6,
bootloader_failure = 7,
eeprom_error = 8,
bist_check_failed = 9,
uctrl_not_responding = 10,
cx3_fifo_overflow = 11,
general_cx3_failure = 12,
cx3_usb_failure = 13,
reserved_1 = 14,
reserved_2 = 15,
max_mm_error
} |
|
enum | power_states : uint32_t {
power_states::PWR_STATE_DNR = 0x00,
power_states::PWR_STATE_INIT = 0x02,
power_states::PWR_STATE_ACTIVE = 0x03,
power_states::PWR_STATE_PAUSE = 0x04,
power_states::PWR_STATE_IAP = 0x05
} |
|