navsat_transform_node

navsat_transform_node takes as input a nav_msgs/Odometry message (usually the output of ekf_localization_node or ukf_localization_node), a sensor_msgs/Imu containing an accurate estimate of your robot’s heading, and a sensor_msgs/NavSatFix message containing GPS data. It produces an odometry message in coordinates that are consistent with your robot’s world frame. This value can be directly fused into your state estimate.

Note

If you fuse the output of this node with any of the state estimation nodes in robot_localization, you should make sure that the odomN_differential setting is false for that input.

Parameters

~frequency

The real-valued frequency, in Hz, at which navsat_transform_node checks for new sensor_msgs/NavSatFix messages, and publishes filtered sensor_msgs/NavSatFix when publish_filtered_gps is set to true.

~delay

The time, in seconds, to wait before calculating the transform from GPS coordinates to your robot’s world frame.

~magnetic_declination_radians

Enter the magnetic declination for your location. If you don’t know it, see http://www.ngdc.noaa.gov/geomag-web (make sure to convert the value to radians). This parameter is needed if your IMU provides its orientation with respect to the magnetic north.

~yaw_offset

Your IMU should read 0 for yaw when facing east. If it doesn’t, enter the offset here (desired_value = offset + sensor_raw_value). For example, if your IMU reports 0 when facing north, as most of them do, this parameter would be pi/2 (~1.5707963). This parameter changed in version 2.2.1. Previously, navsat_transform_node assumed that IMUs read 0 when facing north, so yaw_offset was used acordingly.

~zero_altitude

If this is true, the nav_msgs/Odometry message produced by this node has its pose Z value set to 0.

~publish_filtered_gps

If true, navsat_transform_node will also transform your robot’s world frame (e.g., map) position back to GPS coordinates, and publish a sensor_msgs/NavSatFix message on the /gps/filtered topic.

~broadcast_utm_transform

If this is true, navsat_transform_node will broadcast the transform between the UTM grid and the frame of the input odometry data. See Published Transforms below for more information.

~use_odometry_yaw

If true, navsat_transform_node will not get its heading from the IMU data, but from the input odometry message. Users should take care to only set this to true if your odometry message has orientation data specified in an earth-referenced frame, e.g., as produced by a magnetometer. Additionally, if the odometry source is one of the state estimation nodes in robot_localization, the user should have at least one source of absolute orientation data being fed into the node, with the _differential and _relative parameters set to false.

~wait_for_datum

If true, navsat_transform_node will wait to get a datum from either:

• The datum parameter
• The set_datum service

~broadcast_utm_transform_as_parent_frame

If true, navsat_transform_node will publish the utm->world_frame transform instead of the world_frame->utm transform. Note that for the transform to be published broadcast_utm_transform also has to be set to true.

~transform_timeout

This parameter specifies how long we would like to wait if a transformation is not available yet. Defaults to 0 if not set. The value 0 means we just get us the latest available (see tf2 implementation) transform.

Subscribed Topics

• imu/data A sensor_msgs/Imu message with orientation data
• odometry/filtered A nav_msgs/Odometry message of your robot’s current position. This is needed in the event that your first GPS reading comes after your robot has attained some non-zero pose.
• gps/fix A sensor_msgs/NavSatFix message containing your robot’s GPS coordinates

Published Topics

• odometry/gps A nav_msgs/Odometry message containing the GPS coordinates of your robot, transformed into its world coordinate frame. This message can be directly fused into robot_localization’s state estimation nodes.
• gps/filtered (optional) A sensor_msgs/NavSatFix message containing your robot’s world frame position, transformed into GPS coordinates

Published Transforms

• world_frame->utm (optional) - If the broadcast_utm_transform parameter is set to true, navsat_transform_node calculates a transform from the utm frame to the frame_id of the input odometry data. By default, the utm frame is published as a child of the odometry frame by using the inverse transform. With use of the broadcast_utm_transform_as_parent_frame parameter, the utm frame will be published as a parent of the odometry frame. This is useful if you have multiple robots within one TF tree.