Interrupts and flags management functions. More...

Collaboration diagram for Interrupts and flags management functions:

Functions
void	RNG_ClearFlag (uint8_t RNG_FLAG)
	Clears the RNG flags. More...

void	RNG_ClearITPendingBit (uint8_t RNG_IT)
	Clears the RNG interrupt pending bit(s). More...

FlagStatus	RNG_GetFlagStatus (uint8_t RNG_FLAG)
	Checks whether the specified RNG flag is set or not. More...

ITStatus	RNG_GetITStatus (uint8_t RNG_IT)
	Checks whether the specified RNG interrupt has occurred or not. More...

void	RNG_ITConfig (FunctionalState NewState)
	Enables or disables the RNG interrupt. More...

Detailed Description

Interrupts and flags management functions.

 ===============================================================================
             ##### Interrupts and flags management functions #####
 ===============================================================================  

 [..] This section provides functions allowing to configure the RNG Interrupts and 
      to get the status and clear flags and Interrupts pending bits.
  
 [..] The RNG provides 3 Interrupts sources and 3 Flags:
  
 *** Flags : ***
 ===============
 [..] 
    (#) RNG_FLAG_DRDY :  In the case of the RNG_DR register contains valid 
        random data. it is cleared by reading the valid data(using 
        RNG_GetRandomNumber() function).

    (#) RNG_FLAG_CECS : In the case of a seed error detection. 
      
    (#) RNG_FLAG_SECS : In the case of a clock error detection.
              
 *** Interrupts ***
 ==================
 [..] If enabled, an RNG interrupt is pending :
    
   (#) In the case of the RNG_DR register contains valid random data. 
       This interrupt source is cleared once the RNG_DR register has been read 
       (using RNG_GetRandomNumber() function) until a new valid value is 
       computed; or 
   (#) In the case of a seed error : One of the following faulty sequences has 
       been detected:
       (++) More than 64 consecutive bits at the same value (0 or 1)
       (++) More than 32 consecutive alternance of 0 and 1 (0101010101...01)
       This interrupt source is cleared using RNG_ClearITPendingBit(RNG_IT_SEI)
       function; or
   (#) In the case of a clock error : the PLL48CLK (RNG peripheral clock source) 
       was not correctly detected (fPLL48CLK< fHCLK/16). This interrupt source is
       cleared using RNG_ClearITPendingBit(RNG_IT_CEI) function.
       -@- note In this case, User have to check that the clock controller is 
           correctly configured to provide the RNG clock. 

 *** Managing the RNG controller events : ***
 ============================================
 [..] The user should identify which mode will be used in his application to manage 
      the RNG controller events: Polling mode or Interrupt mode.
  
   (#) In the Polling Mode it is advised to use the following functions:
       (++) RNG_GetFlagStatus() : to check if flags events occur. 
       (++) RNG_ClearFlag()     : to clear the flags events.
  
       -@@- RNG_FLAG_DRDY can not be cleared by RNG_ClearFlag(). it is cleared only 
            by reading the Random number data.      
  
   (#)  In the Interrupt Mode it is advised to use the following functions:
        (++) RNG_ITConfig()       : to enable or disable the interrupt source.
        (++) RNG_GetITStatus()    : to check if Interrupt occurs.
        (++) RNG_ClearITPendingBit() : to clear the Interrupt pending Bit 
             (corresponding Flag).

Function Documentation

void RNG_ClearFlag ( uint8_t RNG_FLAG )

Clears the RNG flags.

Parameters

RNG_FLAG

specifies the flag to clear. This parameter can be any combination of the following values:

RNG_FLAG_CECS: Clock Error Current flag.
RNG_FLAG_SECS: Seed Error Current flag.

Note: RNG_FLAG_DRDY can not be cleared by RNG_ClearFlag() function. This flag is cleared only by reading the Random number data (using RNG_GetRandomNumber() function).

Return values

None

Definition at line 326 of file stm32f4xx_rng.c.

void RNG_ClearITPendingBit ( uint8_t RNG_IT )

Clears the RNG interrupt pending bit(s).

Parameters

RNG_IT

specifies the RNG interrupt pending bit(s) to clear. This parameter can be any combination of the following values:

RNG_IT_CEI: Clock Error Interrupt.
RNG_IT_SEI: Seed Error Interrupt.

Return values

None

Definition at line 372 of file stm32f4xx_rng.c.

FlagStatus RNG_GetFlagStatus ( uint8_t RNG_FLAG )

Checks whether the specified RNG flag is set or not.

Parameters

RNG_FLAG

specifies the RNG flag to check. This parameter can be one of the following values:

RNG_FLAG_DRDY: Data Ready flag.
RNG_FLAG_CECS: Clock Error Current flag.
RNG_FLAG_SECS: Seed Error Current flag.

Return values

The	new state of RNG_FLAG (SET or RESET).

Definition at line 293 of file stm32f4xx_rng.c.

ITStatus RNG_GetITStatus ( uint8_t RNG_IT )

Checks whether the specified RNG interrupt has occurred or not.

Parameters

RNG_IT

specifies the RNG interrupt source to check. This parameter can be one of the following values:

RNG_IT_CEI: Clock Error Interrupt.
RNG_IT_SEI: Seed Error Interrupt.

Return values

The	new state of RNG_IT (SET or RESET).

Definition at line 342 of file stm32f4xx_rng.c.

void RNG_ITConfig ( FunctionalState NewState )

Enables or disables the RNG interrupt.

Note

The RNG provides 3 interrupt sources,

Computed data is ready event (DRDY), and
Seed error Interrupt (SEI) and
Clock error Interrupt (CEI), all these interrupts sources are enabled by setting the IE bit in CR register. However, each interrupt have its specific status bit (see RNG_GetITStatus() function) and clear bit except the DRDY event (see RNG_ClearITPendingBit() function).

Parameters

NewState new state of the RNG interrupt. This parameter can be: ENABLE or DISABLE.

Return values

None

Definition at line 267 of file stm32f4xx_rng.c.

Functions

Detailed Description

Function Documentation