Functions

Interrupts and flags management functions. More...

Collaboration diagram for Interrupts and flags management functions:

Functions

void DMA_ClearFlag (DMA_Stream_TypeDef *DMAy_Streamx, uint32_t DMA_FLAG)
 Clears the DMAy Streamx's pending flags. More...
 
void DMA_ClearITPendingBit (DMA_Stream_TypeDef *DMAy_Streamx, uint32_t DMA_IT)
 Clears the DMAy Streamx's interrupt pending bits. More...
 
FunctionalState DMA_GetCmdStatus (DMA_Stream_TypeDef *DMAy_Streamx)
 Returns the status of EN bit for the specified DMAy Streamx. More...
 
uint32_t DMA_GetFIFOStatus (DMA_Stream_TypeDef *DMAy_Streamx)
 Returns the current DMAy Streamx FIFO filled level. More...
 
FlagStatus DMA_GetFlagStatus (DMA_Stream_TypeDef *DMAy_Streamx, uint32_t DMA_FLAG)
 Checks whether the specified DMAy Streamx flag is set or not. More...
 
ITStatus DMA_GetITStatus (DMA_Stream_TypeDef *DMAy_Streamx, uint32_t DMA_IT)
 Checks whether the specified DMAy Streamx interrupt has occurred or not. More...
 
void DMA_ITConfig (DMA_Stream_TypeDef *DMAy_Streamx, uint32_t DMA_IT, FunctionalState NewState)
 Enables or disables the specified DMAy Streamx interrupts. More...
 

Detailed Description

Interrupts and flags management functions.

 ===============================================================================
              ##### Interrupts and flags management functions #####
 ===============================================================================  
    [..]
    This subsection provides functions allowing to
      (+) Check the DMA enable status
      (+) Check the FIFO status 
      (+) Configure the DMA Interrupts sources and check or clear the flags or 
          pending bits status.  
           
    [..]
      (#) DMA Enable status:
          After configuring the DMA Stream (DMA_Init() function) and enabling 
          the stream, it is recommended to check (or wait until) the DMA Stream 
          is effectively enabled. A Stream may remain disabled if a configuration 
          parameter is wrong. After disabling a DMA Stream, it is also recommended 
          to check (or wait until) the DMA Stream is effectively disabled. 
          If a Stream is disabled while a data transfer is ongoing, the current 
          data will be transferred and the Stream will be effectively disabled 
          only after this data transfer completion.
          To monitor this state it is possible to use the following function:
        (++) FunctionalState DMA_GetCmdStatus(DMA_Stream_TypeDef* DMAy_Streamx); 
 
      (#) FIFO Status:
          It is possible to monitor the FIFO status when a transfer is ongoing 
          using the following function:
        (++) uint32_t DMA_GetFIFOStatus(DMA_Stream_TypeDef* DMAy_Streamx); 
 
      (#) DMA Interrupts and Flags:
          The user should identify which mode will be used in his application 
          to manage the DMA controller events: Polling mode or Interrupt mode. 
    
    *** Polling Mode ***
    ====================
    [..]
    Each DMA stream can be managed through 4 event Flags:
    (x : DMA Stream number )
      (#) DMA_FLAG_FEIFx  : to indicate that a FIFO Mode Transfer Error event occurred.
      (#) DMA_FLAG_DMEIFx : to indicate that a Direct Mode Transfer Error event occurred.
      (#) DMA_FLAG_TEIFx  : to indicate that a Transfer Error event occurred.
      (#) DMA_FLAG_HTIFx  : to indicate that a Half-Transfer Complete event occurred.
      (#) DMA_FLAG_TCIFx  : to indicate that a Transfer Complete event occurred .       
    [..]
    In this Mode it is advised to use the following functions:
      (+) FlagStatus DMA_GetFlagStatus(DMA_Stream_TypeDef* DMAy_Streamx, uint32_t DMA_FLAG);
      (+) void DMA_ClearFlag(DMA_Stream_TypeDef* DMAy_Streamx, uint32_t DMA_FLAG);

    *** Interrupt Mode ***
    ======================
    [..]
    Each DMA Stream can be managed through 4 Interrupts:

    *** Interrupt Source ***
    ========================
    [..]
      (#) DMA_IT_FEIFx  : specifies the interrupt source for the  FIFO Mode Transfer Error event.
      (#) DMA_IT_DMEIFx : specifies the interrupt source for the Direct Mode Transfer Error event.
      (#) DMA_IT_TEIFx  : specifies the interrupt source for the Transfer Error event.
      (#) DMA_IT_HTIFx  : specifies the interrupt source for the Half-Transfer Complete event.
      (#) DMA_IT_TCIFx  : specifies the interrupt source for the a Transfer Complete event. 
    [..]
    In this Mode it is advised to use the following functions:
      (+) void DMA_ITConfig(DMA_Stream_TypeDef* DMAy_Streamx, uint32_t DMA_IT, FunctionalState NewState);
      (+) ITStatus DMA_GetITStatus(DMA_Stream_TypeDef* DMAy_Streamx, uint32_t DMA_IT);
      (+) void DMA_ClearITPendingBit(DMA_Stream_TypeDef* DMAy_Streamx, uint32_t DMA_IT);

Function Documentation

void DMA_ClearFlag ( DMA_Stream_TypeDef DMAy_Streamx,
uint32_t  DMA_FLAG 
)

Clears the DMAy Streamx's pending flags.

Parameters
DMAy_Streamxwhere y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.
DMA_FLAGspecifies the flag to clear. This parameter can be any combination of the following values:
  • DMA_FLAG_TCIFx: Streamx transfer complete flag
  • DMA_FLAG_HTIFx: Streamx half transfer complete flag
  • DMA_FLAG_TEIFx: Streamx transfer error flag
  • DMA_FLAG_DMEIFx: Streamx direct mode error flag
  • DMA_FLAG_FEIFx: Streamx FIFO error flag Where x can be 0 to 7 to select the DMA Stream.
Return values
None

Definition at line 1071 of file stm32f4xx_dma.c.

void DMA_ClearITPendingBit ( DMA_Stream_TypeDef DMAy_Streamx,
uint32_t  DMA_IT 
)

Clears the DMAy Streamx's interrupt pending bits.

Parameters
DMAy_Streamxwhere y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.
DMA_ITspecifies the DMA interrupt pending bit to clear. This parameter can be any combination of the following values:
  • DMA_IT_TCIFx: Streamx transfer complete interrupt
  • DMA_IT_HTIFx: Streamx half transfer complete interrupt
  • DMA_IT_TEIFx: Streamx transfer error interrupt
  • DMA_IT_DMEIFx: Streamx direct mode error interrupt
  • DMA_IT_FEIFx: Streamx FIFO error interrupt Where x can be 0 to 7 to select the DMA Stream.
Return values
None

Definition at line 1252 of file stm32f4xx_dma.c.

FunctionalState DMA_GetCmdStatus ( DMA_Stream_TypeDef DMAy_Streamx)

Returns the status of EN bit for the specified DMAy Streamx.

Parameters
DMAy_Streamxwhere y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.
Note
After configuring the DMA Stream (DMA_Init() function) and enabling the stream, it is recommended to check (or wait until) the DMA Stream is effectively enabled. A Stream may remain disabled if a configuration parameter is wrong. After disabling a DMA Stream, it is also recommended to check (or wait until) the DMA Stream is effectively disabled. If a Stream is disabled while a data transfer is ongoing, the current data will be transferred and the Stream will be effectively disabled only after the transfer of this single data is finished.
Return values
Currentstate of the DMAy Streamx (ENABLE or DISABLE).

Definition at line 943 of file stm32f4xx_dma.c.

uint32_t DMA_GetFIFOStatus ( DMA_Stream_TypeDef DMAy_Streamx)

Returns the current DMAy Streamx FIFO filled level.

Parameters
DMAy_Streamxwhere y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.
Return values
TheFIFO filling state.
  • DMA_FIFOStatus_Less1QuarterFull: when FIFO is less than 1 quarter-full and not empty.
  • DMA_FIFOStatus_1QuarterFull: if more than 1 quarter-full.
  • DMA_FIFOStatus_HalfFull: if more than 1 half-full.
  • DMA_FIFOStatus_3QuartersFull: if more than 3 quarters-full.
  • DMA_FIFOStatus_Empty: when FIFO is empty
  • DMA_FIFOStatus_Full: when FIFO is full

Definition at line 977 of file stm32f4xx_dma.c.

FlagStatus DMA_GetFlagStatus ( DMA_Stream_TypeDef DMAy_Streamx,
uint32_t  DMA_FLAG 
)

Checks whether the specified DMAy Streamx flag is set or not.

Parameters
DMAy_Streamxwhere y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.
DMA_FLAGspecifies the flag to check. This parameter can be one of the following values:
  • DMA_FLAG_TCIFx: Streamx transfer complete flag
  • DMA_FLAG_HTIFx: Streamx half transfer complete flag
  • DMA_FLAG_TEIFx: Streamx transfer error flag
  • DMA_FLAG_DMEIFx: Streamx direct mode error flag
  • DMA_FLAG_FEIFx: Streamx FIFO error flag Where x can be 0 to 7 to select the DMA Stream.
Return values
Thenew state of DMA_FLAG (SET or RESET).

Definition at line 1004 of file stm32f4xx_dma.c.

ITStatus DMA_GetITStatus ( DMA_Stream_TypeDef DMAy_Streamx,
uint32_t  DMA_IT 
)

Checks whether the specified DMAy Streamx interrupt has occurred or not.

Parameters
DMAy_Streamxwhere y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.
DMA_ITspecifies the DMA interrupt source to check. This parameter can be one of the following values:
  • DMA_IT_TCIFx: Streamx transfer complete interrupt
  • DMA_IT_HTIFx: Streamx half transfer complete interrupt
  • DMA_IT_TEIFx: Streamx transfer error interrupt
  • DMA_IT_DMEIFx: Streamx direct mode error interrupt
  • DMA_IT_FEIFx: Streamx FIFO error interrupt Where x can be 0 to 7 to select the DMA Stream.
Return values
Thenew state of DMA_IT (SET or RESET).

Definition at line 1170 of file stm32f4xx_dma.c.

void DMA_ITConfig ( DMA_Stream_TypeDef DMAy_Streamx,
uint32_t  DMA_IT,
FunctionalState  NewState 
)

Enables or disables the specified DMAy Streamx interrupts.

Parameters
DMAy_Streamxwhere y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.
DMA_ITspecifies the DMA interrupt sources to be enabled or disabled. This parameter can be any combination of the following values:
  • DMA_IT_TC: Transfer complete interrupt mask
  • DMA_IT_HT: Half transfer complete interrupt mask
  • DMA_IT_TE: Transfer error interrupt mask
  • DMA_IT_FE: FIFO error interrupt mask
NewStatenew state of the specified DMA interrupts. This parameter can be: ENABLE or DISABLE.
Return values
None

Definition at line 1118 of file stm32f4xx_dma.c.



rosflight_firmware
Author(s): Daniel Koch , James Jackson
autogenerated on Wed Jul 3 2019 19:59:29