Classes | |
| struct | Acc |
| Acc hardware registers. More... | |
Macros | |
| #define | ACC_ACR_HYST(value) ((ACC_ACR_HYST_Msk & ((value) << ACC_ACR_HYST_Pos))) |
| #define | ACC_ACR_HYST_Msk (0x3u << ACC_ACR_HYST_Pos) |
| (ACC_ACR) Hysteresis Selection More... | |
| #define | ACC_ACR_HYST_Pos 1 |
| #define | ACC_ACR_ISEL (0x1u << 0) |
| (ACC_ACR) Current Selection More... | |
| #define | ACC_ACR_ISEL_HISP (0x1u << 0) |
| (ACC_ACR) High-speed option. More... | |
| #define | ACC_ACR_ISEL_LOPW (0x0u << 0) |
| (ACC_ACR) Low-power option. More... | |
| #define | ACC_CR_SWRST (0x1u << 0) |
| (ACC_CR) Software Reset More... | |
| #define | ACC_IDR_CE (0x1u << 0) |
| (ACC_IDR) Comparison Edge More... | |
| #define | ACC_IER_CE (0x1u << 0) |
| (ACC_IER) Comparison Edge More... | |
| #define | ACC_IMR_CE (0x1u << 0) |
| (ACC_IMR) Comparison Edge More... | |
| #define | ACC_ISR_CE (0x1u << 0) |
| (ACC_ISR) Comparison Edge (cleared on read) More... | |
| #define | ACC_ISR_MASK (0x1u << 31) |
| (ACC_ISR) Flag Mask More... | |
| #define | ACC_ISR_SCO (0x1u << 1) |
| (ACC_ISR) Synchronized Comparator Output More... | |
| #define | ACC_MR_ACEN (0x1u << 8) |
| (ACC_MR) Analog Comparator Enable More... | |
| #define | ACC_MR_ACEN_DIS (0x0u << 8) |
| (ACC_MR) Analog comparator disabled. More... | |
| #define | ACC_MR_ACEN_EN (0x1u << 8) |
| (ACC_MR) Analog comparator enabled. More... | |
| #define | ACC_MR_EDGETYP(value) ((ACC_MR_EDGETYP_Msk & ((value) << ACC_MR_EDGETYP_Pos))) |
| #define | ACC_MR_EDGETYP_ANY (0x2u << 9) |
| (ACC_MR) Any edge of comparator output More... | |
| #define | ACC_MR_EDGETYP_FALLING (0x1u << 9) |
| (ACC_MR) Falling edge of comparator output More... | |
| #define | ACC_MR_EDGETYP_Msk (0x3u << ACC_MR_EDGETYP_Pos) |
| (ACC_MR) Edge Type More... | |
| #define | ACC_MR_EDGETYP_Pos 9 |
| #define | ACC_MR_EDGETYP_RISING (0x0u << 9) |
| (ACC_MR) Only rising edge of comparator output More... | |
| #define | ACC_MR_FE (0x1u << 14) |
| (ACC_MR) Fault Enable More... | |
| #define | ACC_MR_FE_DIS (0x0u << 14) |
| (ACC_MR) The FAULT output is tied to 0. More... | |
| #define | ACC_MR_FE_EN (0x1u << 14) |
| (ACC_MR) The FAULT output is driven by the signal defined by SELFS. More... | |
| #define | ACC_MR_INV (0x1u << 12) |
| (ACC_MR) Invert Comparator Output More... | |
| #define | ACC_MR_INV_DIS (0x0u << 12) |
| (ACC_MR) Analog comparator output is directly processed. More... | |
| #define | ACC_MR_INV_EN (0x1u << 12) |
| (ACC_MR) Analog comparator output is inverted prior to being processed. More... | |
| #define | ACC_MR_SELFS (0x1u << 13) |
| (ACC_MR) Selection Of Fault Source More... | |
| #define | ACC_MR_SELFS_CE (0x0u << 13) |
| (ACC_MR) The CE flag is used to drive the FAULT output. More... | |
| #define | ACC_MR_SELFS_OUTPUT (0x1u << 13) |
| (ACC_MR) The output of the analog comparator flag is used to drive the FAULT output. More... | |
| #define | ACC_MR_SELMINUS(value) ((ACC_MR_SELMINUS_Msk & ((value) << ACC_MR_SELMINUS_Pos))) |
| #define | ACC_MR_SELMINUS_ADVREFP (0x1u << 0) |
| (ACC_MR) Select ADVREFP More... | |
| #define | ACC_MR_SELMINUS_AFE0_AD0 (0x4u << 0) |
| (ACC_MR) Select AFE0_AD0 More... | |
| #define | ACC_MR_SELMINUS_AFE0_AD1 (0x5u << 0) |
| (ACC_MR) Select AFE0_AD1 More... | |
| #define | ACC_MR_SELMINUS_AFE0_AD2 (0x6u << 0) |
| (ACC_MR) Select AFE0_AD2 More... | |
| #define | ACC_MR_SELMINUS_AFE0_AD3 (0x7u << 0) |
| (ACC_MR) Select AFE0_AD3 More... | |
| #define | ACC_MR_SELMINUS_DAC0 (0x2u << 0) |
| (ACC_MR) Select DAC0 More... | |
| #define | ACC_MR_SELMINUS_DAC1 (0x3u << 0) |
| (ACC_MR) Select DAC1 More... | |
| #define | ACC_MR_SELMINUS_Msk (0x7u << ACC_MR_SELMINUS_Pos) |
| (ACC_MR) Selection for Minus Comparator Input More... | |
| #define | ACC_MR_SELMINUS_Pos 0 |
| #define | ACC_MR_SELMINUS_TS (0x0u << 0) |
| (ACC_MR) Select TS More... | |
| #define | ACC_MR_SELMINUS_VREFP (0x1u << 0) |
| (ACC_MR) Select VREFP More... | |
| #define | ACC_MR_SELPLUS(value) ((ACC_MR_SELPLUS_Msk & ((value) << ACC_MR_SELPLUS_Pos))) |
| #define | ACC_MR_SELPLUS_AFE0_AD0 (0x0u << 4) |
| (ACC_MR) Select AFE0_AD0 More... | |
| #define | ACC_MR_SELPLUS_AFE0_AD1 (0x1u << 4) |
| (ACC_MR) Select AFE0_AD1 More... | |
| #define | ACC_MR_SELPLUS_AFE0_AD2 (0x2u << 4) |
| (ACC_MR) Select AFE0_AD2 More... | |
| #define | ACC_MR_SELPLUS_AFE0_AD3 (0x3u << 4) |
| (ACC_MR) Select AFE0_AD3 More... | |
| #define | ACC_MR_SELPLUS_AFE0_AD4 (0x4u << 4) |
| (ACC_MR) Select AFE0_AD4 More... | |
| #define | ACC_MR_SELPLUS_AFE0_AD5 (0x5u << 4) |
| (ACC_MR) Select AFE0_AD5 More... | |
| #define | ACC_MR_SELPLUS_AFE1_AD0 (0x6u << 4) |
| (ACC_MR) Select AFE1_AD0 More... | |
| #define | ACC_MR_SELPLUS_AFE1_AD1 (0x7u << 4) |
| (ACC_MR) Select AFE1_AD1 More... | |
| #define | ACC_MR_SELPLUS_Msk (0x7u << ACC_MR_SELPLUS_Pos) |
| (ACC_MR) Selection For Plus Comparator Input More... | |
| #define | ACC_MR_SELPLUS_Pos 4 |
| #define | ACC_VER_MFN_Msk (0x7u << ACC_VER_MFN_Pos) |
| (ACC_VER) Metal Fix Number More... | |
| #define | ACC_VER_MFN_Pos 16 |
| #define | ACC_VER_VERSION_Msk (0xfffu << ACC_VER_VERSION_Pos) |
| (ACC_VER) Version of the Hardware Module More... | |
| #define | ACC_VER_VERSION_Pos 0 |
| #define | ACC_WPMR_WPEN (0x1u << 0) |
| (ACC_WPMR) Write Protection Enable More... | |
| #define | ACC_WPMR_WPKEY(value) ((ACC_WPMR_WPKEY_Msk & ((value) << ACC_WPMR_WPKEY_Pos))) |
| #define | ACC_WPMR_WPKEY_Msk (0xffffffu << ACC_WPMR_WPKEY_Pos) |
| (ACC_WPMR) Write Protection Key More... | |
| #define | ACC_WPMR_WPKEY_PASSWD (0x414343u << 8) |
| (ACC_WPMR) Writing any other value in this field aborts the write operation of the WPEN bit.Always reads as 0. More... | |
| #define | ACC_WPMR_WPKEY_Pos 8 |
| #define | ACC_WPSR_WPVS (0x1u << 0) |
| (ACC_WPSR) Write Protection Violation Status More... | |
SOFTWARE API DEFINITION FOR Analog Comparator Controller
| #define ACC_ACR_HYST | ( | value | ) | ((ACC_ACR_HYST_Msk & ((value) << ACC_ACR_HYST_Pos))) |
Definition at line 123 of file component/acc.h.
| #define ACC_ACR_HYST_Msk (0x3u << ACC_ACR_HYST_Pos) |
(ACC_ACR) Hysteresis Selection
Definition at line 122 of file component/acc.h.
| #define ACC_ACR_HYST_Pos 1 |
Definition at line 121 of file component/acc.h.
| #define ACC_ACR_ISEL (0x1u << 0) |
(ACC_ACR) Current Selection
Definition at line 118 of file component/acc.h.
| #define ACC_ACR_ISEL_HISP (0x1u << 0) |
(ACC_ACR) High-speed option.
Definition at line 120 of file component/acc.h.
| #define ACC_ACR_ISEL_LOPW (0x0u << 0) |
(ACC_ACR) Low-power option.
Definition at line 119 of file component/acc.h.
| #define ACC_CR_SWRST (0x1u << 0) |
(ACC_CR) Software Reset
Definition at line 64 of file component/acc.h.
| #define ACC_IDR_CE (0x1u << 0) |
(ACC_IDR) Comparison Edge
Definition at line 110 of file component/acc.h.
| #define ACC_IER_CE (0x1u << 0) |
(ACC_IER) Comparison Edge
Definition at line 108 of file component/acc.h.
| #define ACC_IMR_CE (0x1u << 0) |
(ACC_IMR) Comparison Edge
Definition at line 112 of file component/acc.h.
| #define ACC_ISR_CE (0x1u << 0) |
(ACC_ISR) Comparison Edge (cleared on read)
Definition at line 114 of file component/acc.h.
| #define ACC_ISR_MASK (0x1u << 31) |
(ACC_ISR) Flag Mask
Definition at line 116 of file component/acc.h.
| #define ACC_ISR_SCO (0x1u << 1) |
(ACC_ISR) Synchronized Comparator Output
Definition at line 115 of file component/acc.h.
| #define ACC_MR_ACEN (0x1u << 8) |
(ACC_MR) Analog Comparator Enable
Definition at line 89 of file component/acc.h.
| #define ACC_MR_ACEN_DIS (0x0u << 8) |
(ACC_MR) Analog comparator disabled.
Definition at line 90 of file component/acc.h.
| #define ACC_MR_ACEN_EN (0x1u << 8) |
(ACC_MR) Analog comparator enabled.
Definition at line 91 of file component/acc.h.
| #define ACC_MR_EDGETYP | ( | value | ) | ((ACC_MR_EDGETYP_Msk & ((value) << ACC_MR_EDGETYP_Pos))) |
Definition at line 94 of file component/acc.h.
| #define ACC_MR_EDGETYP_ANY (0x2u << 9) |
(ACC_MR) Any edge of comparator output
Definition at line 97 of file component/acc.h.
| #define ACC_MR_EDGETYP_FALLING (0x1u << 9) |
(ACC_MR) Falling edge of comparator output
Definition at line 96 of file component/acc.h.
| #define ACC_MR_EDGETYP_Msk (0x3u << ACC_MR_EDGETYP_Pos) |
(ACC_MR) Edge Type
Definition at line 93 of file component/acc.h.
| #define ACC_MR_EDGETYP_Pos 9 |
Definition at line 92 of file component/acc.h.
| #define ACC_MR_EDGETYP_RISING (0x0u << 9) |
(ACC_MR) Only rising edge of comparator output
Definition at line 95 of file component/acc.h.
| #define ACC_MR_FE (0x1u << 14) |
(ACC_MR) Fault Enable
Definition at line 104 of file component/acc.h.
| #define ACC_MR_FE_DIS (0x0u << 14) |
(ACC_MR) The FAULT output is tied to 0.
Definition at line 105 of file component/acc.h.
| #define ACC_MR_FE_EN (0x1u << 14) |
(ACC_MR) The FAULT output is driven by the signal defined by SELFS.
Definition at line 106 of file component/acc.h.
| #define ACC_MR_INV (0x1u << 12) |
(ACC_MR) Invert Comparator Output
Definition at line 98 of file component/acc.h.
| #define ACC_MR_INV_DIS (0x0u << 12) |
(ACC_MR) Analog comparator output is directly processed.
Definition at line 99 of file component/acc.h.
| #define ACC_MR_INV_EN (0x1u << 12) |
(ACC_MR) Analog comparator output is inverted prior to being processed.
Definition at line 100 of file component/acc.h.
| #define ACC_MR_SELFS (0x1u << 13) |
(ACC_MR) Selection Of Fault Source
Definition at line 101 of file component/acc.h.
| #define ACC_MR_SELFS_CE (0x0u << 13) |
(ACC_MR) The CE flag is used to drive the FAULT output.
Definition at line 102 of file component/acc.h.
| #define ACC_MR_SELFS_OUTPUT (0x1u << 13) |
(ACC_MR) The output of the analog comparator flag is used to drive the FAULT output.
Definition at line 103 of file component/acc.h.
| #define ACC_MR_SELMINUS | ( | value | ) | ((ACC_MR_SELMINUS_Msk & ((value) << ACC_MR_SELMINUS_Pos))) |
Definition at line 68 of file component/acc.h.
| #define ACC_MR_SELMINUS_ADVREFP (0x1u << 0) |
(ACC_MR) Select ADVREFP
Definition at line 70 of file component/acc.h.
| #define ACC_MR_SELMINUS_AFE0_AD0 (0x4u << 0) |
(ACC_MR) Select AFE0_AD0
Definition at line 74 of file component/acc.h.
| #define ACC_MR_SELMINUS_AFE0_AD1 (0x5u << 0) |
(ACC_MR) Select AFE0_AD1
Definition at line 75 of file component/acc.h.
| #define ACC_MR_SELMINUS_AFE0_AD2 (0x6u << 0) |
(ACC_MR) Select AFE0_AD2
Definition at line 76 of file component/acc.h.
| #define ACC_MR_SELMINUS_AFE0_AD3 (0x7u << 0) |
(ACC_MR) Select AFE0_AD3
Definition at line 77 of file component/acc.h.
| #define ACC_MR_SELMINUS_DAC0 (0x2u << 0) |
(ACC_MR) Select DAC0
Definition at line 72 of file component/acc.h.
| #define ACC_MR_SELMINUS_DAC1 (0x3u << 0) |
(ACC_MR) Select DAC1
Definition at line 73 of file component/acc.h.
| #define ACC_MR_SELMINUS_Msk (0x7u << ACC_MR_SELMINUS_Pos) |
(ACC_MR) Selection for Minus Comparator Input
Definition at line 67 of file component/acc.h.
| #define ACC_MR_SELMINUS_Pos 0 |
Definition at line 66 of file component/acc.h.
| #define ACC_MR_SELMINUS_TS (0x0u << 0) |
(ACC_MR) Select TS
Definition at line 69 of file component/acc.h.
| #define ACC_MR_SELMINUS_VREFP (0x1u << 0) |
(ACC_MR) Select VREFP
Definition at line 71 of file component/acc.h.
| #define ACC_MR_SELPLUS | ( | value | ) | ((ACC_MR_SELPLUS_Msk & ((value) << ACC_MR_SELPLUS_Pos))) |
Definition at line 80 of file component/acc.h.
| #define ACC_MR_SELPLUS_AFE0_AD0 (0x0u << 4) |
(ACC_MR) Select AFE0_AD0
Definition at line 81 of file component/acc.h.
| #define ACC_MR_SELPLUS_AFE0_AD1 (0x1u << 4) |
(ACC_MR) Select AFE0_AD1
Definition at line 82 of file component/acc.h.
| #define ACC_MR_SELPLUS_AFE0_AD2 (0x2u << 4) |
(ACC_MR) Select AFE0_AD2
Definition at line 83 of file component/acc.h.
| #define ACC_MR_SELPLUS_AFE0_AD3 (0x3u << 4) |
(ACC_MR) Select AFE0_AD3
Definition at line 84 of file component/acc.h.
| #define ACC_MR_SELPLUS_AFE0_AD4 (0x4u << 4) |
(ACC_MR) Select AFE0_AD4
Definition at line 85 of file component/acc.h.
| #define ACC_MR_SELPLUS_AFE0_AD5 (0x5u << 4) |
(ACC_MR) Select AFE0_AD5
Definition at line 86 of file component/acc.h.
| #define ACC_MR_SELPLUS_AFE1_AD0 (0x6u << 4) |
(ACC_MR) Select AFE1_AD0
Definition at line 87 of file component/acc.h.
| #define ACC_MR_SELPLUS_AFE1_AD1 (0x7u << 4) |
(ACC_MR) Select AFE1_AD1
Definition at line 88 of file component/acc.h.
| #define ACC_MR_SELPLUS_Msk (0x7u << ACC_MR_SELPLUS_Pos) |
(ACC_MR) Selection For Plus Comparator Input
Definition at line 79 of file component/acc.h.
| #define ACC_MR_SELPLUS_Pos 4 |
Definition at line 78 of file component/acc.h.
| #define ACC_VER_MFN_Msk (0x7u << ACC_VER_MFN_Pos) |
(ACC_VER) Metal Fix Number
Definition at line 136 of file component/acc.h.
| #define ACC_VER_MFN_Pos 16 |
Definition at line 135 of file component/acc.h.
| #define ACC_VER_VERSION_Msk (0xfffu << ACC_VER_VERSION_Pos) |
(ACC_VER) Version of the Hardware Module
Definition at line 134 of file component/acc.h.
| #define ACC_VER_VERSION_Pos 0 |
Definition at line 133 of file component/acc.h.
| #define ACC_WPMR_WPEN (0x1u << 0) |
(ACC_WPMR) Write Protection Enable
Definition at line 125 of file component/acc.h.
| #define ACC_WPMR_WPKEY | ( | value | ) | ((ACC_WPMR_WPKEY_Msk & ((value) << ACC_WPMR_WPKEY_Pos))) |
Definition at line 128 of file component/acc.h.
| #define ACC_WPMR_WPKEY_Msk (0xffffffu << ACC_WPMR_WPKEY_Pos) |
(ACC_WPMR) Write Protection Key
Definition at line 127 of file component/acc.h.
| #define ACC_WPMR_WPKEY_PASSWD (0x414343u << 8) |
(ACC_WPMR) Writing any other value in this field aborts the write operation of the WPEN bit.Always reads as 0.
Definition at line 129 of file component/acc.h.
| #define ACC_WPMR_WPKEY_Pos 8 |
Definition at line 126 of file component/acc.h.
| #define ACC_WPSR_WPVS (0x1u << 0) |
(ACC_WPSR) Write Protection Violation Status
Definition at line 131 of file component/acc.h.