Preparing Your Data for Use with robot_localization

Before getting started with the state estimation nodes in robot_localization, it is important that users ensure that their sensor data well-formed. There are various considerations for each class of sensor data, and users are encouraged to read this tutorial in its entirety before attempting to use robot_localization.

For additional information, users are encouraged to watch this presentation from ROSCon 2015.

Adherence to ROS Standards

The two most important ROS REPs to consider are:

  • REP-103 (Standard Units of Measure and Coordinate Conventions)
  • REP-105 (Coordinate Frame Conventions).

Users who are new to ROS or state estimation are encouraged to read over both REPs, as it will almost certainly aid you in preparing your sensor data. robot_localization attempts to adhere to these standards as much as possible.

Also, it will likely benefit users to look over the specifications for each of the supported ROS message types:

Coordinate Frames and Transforming Sensor Data

REP-105 specifies four principal coordinate frames: base_link, odom, map, and earth. The base_link frame is rigidly affixed to the robot. The map and odom frames are world-fixed frames whose origins are typically aligned with the robot’s start position. The earth frame is used to provide a common reference frame for multiple map frames (e.g., for robots distributed over a large area). The earth frame is not relevant to this tutorial.

The state estimation nodes of robot_localization produce a state estimate whose pose is given in the map or odom frame and whose velocity is given in the base_link frame. All incoming data is transformed into one of these coordinate frames before being fused with the state. The data in each message type is transformed as follows:

  • nav_msgs/Odometry - All pose data (position and orientation) is transformed from the message header’s frame_id into the coordinate frame specified by the world_frame parameter (typically map or odom). In the message itself, this specifically refers to everything contained within the pose property. All twist data (linear and angular velocity) is transformed from the child_frame_id of the message into the coordinate frame specified by the base_link_frame parameter (typically base_link).
  • geometry_msgs/PoseWithCovarianceStamped - Handled in the same fashion as the pose data in the Odometry message.
  • geometry_msgs/TwistWithCovarianceStamped - Handled in the same fashion as the twist data in the Odometry message.
  • sensor_msgs/Imu - The IMU message is currently subject to some ambiguity, though this is being addressed by the ROS community. Most IMUs natively report orientation data in a world-fixed frame whose \(X\) and \(Z\) axes are defined by the vectors pointing to magnetic north and the center of the earth, respectively, with the Y axis facing east (90 degrees offset from the magnetic north vector). This frame is often referred to as NED (North, East, Down). However, REP-103 specifies an ENU (East, North, Up) coordinate frame for outdoor navigation. As of this writing, robot_localization assumes an ENU frame for all IMU data, and does not work with NED frame data. This may change in the future, but for now, users should ensure that data is transformed to the ENU frame before using it with any node in robot_localization.

The IMU may also be oriented on the robot in a position other than its “neutral” position. For example, the user may mount the IMU on its side, or rotate it so that it faces a direction other than the front of the robot. This offset is typically specified by a static transform from the base_link_frame parameter to the IMU message’s frame_id. The state estimation nodes in robot_localization will automatically correct for the orientation of the sensor so that its data aligns with the frame specified by the base_link_frame parameter.

Handling tf_prefix

With the migration to tf2 as of ROS Indigo, robot_localization still allows for the use of the tf_prefix parameter, but, in accordance with tf2, all frame_id values will have any leading ‘/’ stripped.

Considerations for Each Sensor Message Type


Many robot platforms come equipped with wheel encoders that provide instantaneous translational and rotational velocity. Many also internally integrate these velocities to generate a position estimate. If you are responsible for this data, or can edit it, keep the following in mind:

  1. Velocities/Poses: robot_localization can integrate velocities or absolute pose information. In general, the best practice is:
  • If the odometry provides both position and linear velocity, fuse the linear velocity.
  • If the odometry provides both orientation and angular velocity, fuse the orientation.


If you have two sources of orientation data, then you’ll want to be careful. If both produce orientations with accurate covariance matrices, it’s safe to fuse the orientations. If, however, one or both under-reports its covariance, then you should only fuse the orientation data from the more accurate sensor. For the other sensor, use the angular velocity (if it’s provided), or continue to fuse the absolute orientation data, but turn _differential mode on for that sensor.

  1. frame_id: See the section on coordinate frames and transforms above.
  2. Covariance: Covariance values matter to robot_localization. robot_pose_ekf attempts to fuse all pose variables in an odometry message. Some robots’ drivers have been written to accommodate its requirements. This means that if a given sensor does not produce a certain variable (e.g., a robot that doesn’t report \(Z\) position), then the only way to get robot_pose_ekf to ignore it is to inflate its variance to a very large value (on the order of \(1e3\)) so that the variable in question is effectively ignored. This practice is both unnecessary and even detrimental to the performance of robot_localization. The exception is the case where you have a second input source measuring the variable in question, in which case inflated covariances will work.
  1. Signs: Adherence to REP-103 means that you need to ensure that the signs of your data are correct. For example, if you have a ground robot and turn it counter-clockwise, then its yaw angle should increase, and its yaw velocity should be positive. If you drive it forward, its X-position should increase and its X-velocity should be positive.
  2. Transforms: Broadcast of the odom->*base_link* transform. When the world_frame parameter is set to the value of the odom_frame parameter in the configuration file, robot_localization‘s state estimation nodes output both a position estimate in a nav_msgs/Odometry message and a transform from the frame specified by its odom_frame parameter to its base_link_frame parameter. However, some robot drivers also broadcast this transform along with their odometry message. If users want robot_localization to be responsible for this transform, then they need to disable the broadcast of that transform by their robot’s driver. This is often exposed as a parameter.


In addition to the following, be sure to read the above section regarding coordinate frames and transforms for IMU data.

  1. Adherence to specifications: As with odometry, be sure your data adheres to REP-103 and the sensor_msgs/Imu specification. Double-check the signs of your data, and make sure the frame_id values are correct.
  2. Covariance: Echoing the advice for odometry, make sure your covariances make sense. Do not use large values to get the filter to ignore a given variable. Set the configuration for the variable you’d like to ignore to false.
  3. Acceleration: Be careful with acceleration data. The state estimation nodes in robot_localization assume that an IMU that is placed in its neutral right-side-up position on a flat surface will:
  • Measure +\(9.81\) meters per second squared for the \(Z\) axis.
  • If the sensor is rolled +\(90\) degrees (left side up), the acceleration should be +\(9.81\) meters per second squared for the \(Y\) axis.
  • If the sensor is pitched +\(90\) degrees (front side down), it should read -\(9.81\) meters per second squared for the \(X\) axis.


See the section on odometry.


See the section on odometry.

Common errors

  • Input data doesn’t adhere to REP-103. Make sure that all values (especially orientation angles) increase and decrease in the correct directions.
  • Incorrect frame_id values. Velocity data should be reported in the frame given by the base_link_frame parameter, or a transform should exist between the frame_id of the velocity data and the base_link_frame.
  • Inflated covariances. The preferred method for ignoring variables in measurements is through the odomN_config parameter.
  • Missing covariances. If you have configured a given sensor to fuse a given variable into the state estimation node, then the variance for that value (i.e., the covariance matrix value at position \((i, i)\), where \(i\) is the index of that variable) should not be \(0\). If a \(0\) variance value is encountered for a variable that is being fused, the state estimation nodes will add a small epsilon value (\(1e^{-6}\)) to that value. A better solution is for users to set covariances appropriately.