stop_line.cc

Go to the documentation of this file.

/*
 *  Navigator stop line controller
 *
 *  Copyright (C) 2007, 2010, Austin Robot Technology
 *  License: Modified BSD Software License Agreement
 *
 *  $Id: stop_line.cc 872 2010-11-28 13:31:07Z jack.oquin $
 */

#include <art_msgs/ArtVehicle.h>
using art_msgs::ArtVehicle;

#include <art/DARPA_rules.h>
#include "navigator_internal.h"
#include "Controller.h"
#include "course.h"
#include "stop_line.h"

StopLine::StopLine(Navigator *navptr, int _verbose):
  Controller(navptr, _verbose)
{
  reset_me();
};

StopLine::~StopLine() {};

Controller::result_t StopLine::control(pilot_command_t &pcmd,
                                       float topspeed)
{
  result_t result = OK;

  // distance from front bumper to stop way-point
  float wayptdist =
    (Euclidean::DistanceToWaypt(MapPose(estimate->pose.pose),
                                course->stop_waypt)
     - ArtVehicle::front_bumper_px + config_->stop_distance);
  // stop_latency compensates for latency in the braking system.
  float abs_speed = fabsf(estimate->twist.twist.linear.x);
  float latencydist = abs_speed * config_->stop_latency;
  float D = wayptdist - latencydist;

  // According to the model, deceleration should be constant, but in
  // the real world control latency will cause it to vary, so apply
  // feedback and recompute the model every cycle.
  if (abs_speed < Epsilon::speed)
    abs_speed = 0.0;

  float V = -abs_speed;
  float A = V*V/(2.0*D);
  ElementID stop_id = course->stop_waypt.id;
  
  // see if it is time to begin stopping
  if ((D <= config_->min_stop_distance || A >= config_->stop_deceleration)
      && !stopping)
    {
      stopping = true;
      initial_speed = fmaxf(topspeed,abs_speed);
      ART_MSG(8, "begin stopping for waypoint %s",
              stop_id.name().str);
    }

  // Once stopping is initiated, keep doing it until reset(), no
  // matter how V changes.
  if (stopping)
    {

      // check whether front bumper is within stop way-point polygon
      Polar front_bumper(0.0, ArtVehicle::front_bumper_px);

      if (D <= config_->stop_distance ||
          pops->pointInPoly(front_bumper, MapPose(estimate->pose.pose),
                            course->stop_poly))
        {
          pcmd.velocity = 0.0;          // halt immediately.

          // report Finished when stopped within stop polygon
          if (abs_speed < Epsilon::speed)
            {
              // Consider this way-point "reached".
              course->new_waypoint_reached(stop_id);
              course->stop_waypt.id = ElementID(); // reset way-point
              result = Finished;
            }
        }
      else if (!creeping && abs_speed >= Epsilon::speed)
        {
          // Not there yet.  Do not let the requested speed increase
          // above initial speed when stopping began, even when the
          // car was accelerating.
          pcmd.velocity = fminf(pcmd.velocity, abs_speed - A);
          pcmd.velocity = fminf(pcmd.velocity, initial_speed);
          if (pcmd.velocity < 0.0)
            pcmd.velocity = 0.0;        // do not change direction
        }
      else if (D <= config_->max_creep_distance)
        {
          creeping=true;
          // stopped too soon, keep creeping forward
          pcmd.velocity = fminf(pcmd.velocity, config_->stop_creep_speed);
        }

      if (verbose >= 2)
        {
          ART_MSG(8, "stop %.3f m away for waypoint %s (%.3f,%.3f),"
                  " %.3f m latency",
                  wayptdist - config_->stop_distance, stop_id.name().str,
                  course->stop_waypt.map.x, course->stop_waypt.map.y,
                  latencydist);
          ART_MSG(8, "current, desired speed %.3f m/s, %.3f m/s,"
                  " decel %.3f m/s/s",
                  abs_speed, pcmd.velocity, A);
        }
    }

  trace("stop_line controller", pcmd, result);
  return result;
};

// reset controller and any subordinates
void StopLine::reset(void)
{
  trace_reset("StopLine");
  reset_me();
};

// reset this controller only
void StopLine::reset_me(void)
{
  stopping = false;
  creeping = false;
  initial_speed = 0.0;
};

---

art_nav
Author(s): Austin Robot Technology, Jack O'Quin
autogenerated on Fri Jan 11 10:05:25 2013