Usage

Launch files

For starting the driver there are two main launch files in the ur_robot_driver package.

ur_control.launch.py - starts ros2_control node including hardware interface, joint state broadcaster and a controller. This launch file also starts dashboard_client if real robot is used.
ur_dashboard_client.launch.py - start the dashboard client for UR robots.

Also, there are predefined launch files for all supported types of UR robots.

The arguments for launch files can be listed using ros2 launch ur_robot_driver <launch_file_name>.launch.py --show-args. The most relevant arguments are the following:

ur_type (mandatory ) - a type of used UR robot (ur3, ur3e, ur5, ur5e, ur10, ur10e, or ur16e, ur20, ur30).
robot_ip (mandatory ) - IP address by which the root can be reached.
use_fake_hardware (default: false ) - use simple hardware emulator from ros2_control. Useful for testing launch files, descriptions, etc. See explanation below.
initial_positions (default: dictionary with all joint values set to 0) - Allows passing a dictionary to set the initial joint values for the fake hardware from ros2_control. It can also be set from a yaml file with the load_yaml commands as follows:
```
<xacro:property name="initial_positions" value="${load_yaml(initial_positions_file)}" / >
```
In this example, the initial_positions_file is a xacro argument that contains the absolute path to a yaml file. An example of the initial positions yaml file is as follows:
```
elbow_joint: 1.158
shoulder_lift_joint: -0.953
shoulder_pan_joint: 1.906
wrist_1_joint: -1.912
wrist_2_joint: -1.765
wrist_3_joint: 0.0
```
fake_sensor_commands (default: false ) - enables setting sensor values for the hardware emulators. Useful for offline testing of controllers.
robot_controller (default: joint_trajectory_controller ) - controller for robot joints to be started. Available controllers:
- joint_trajectory_controller
- scaled_joint_trajectory_controller
Note: joint_state_broadcaster, speed_scaling_state_broadcaster, force_torque_sensor_broadcaster, and io_and_status_controller will always start.

HINT : list all loaded controllers using ros2 control list_controllers command.

NOTE: The package can simulate hardware with the ros2_control FakeSystem. This emulator enables an environment for testing of “piping” of hardware and controllers, as well as testing robot’s descriptions. For more details see ros2_control documentation for more details.

Modes of operation

As mentioned in the last section the driver has two basic modes of operation: Using fake hardware or using real hardware(Or the URSim simulator, which is equivalent from the driver’s perspective). Additionally, the robot can be simulated using Gazebo or ignition but that’s outside of this driver’s scope.

mode

available controllers

fake_hardware

joint_trajectory_controller
forward_velocity_controller
forward_position_controller

real hardware / URSim

joint_trajectory_controller
scaled_joint_trajectory_controller
forward_velocity_controller
forward_position_controller

Usage with official UR simulator

The easiest way to use URSim is the Docker image provided by Universal Robots (See this link for a CB3-series image).

To start it, we’ve prepared a script:

ros2 run ur_client_library start_ursim.sh -m <ur_type>

With this, we can spin up a driver using

ros2 launch ur_robot_driver ur_control.launch.py ur_type:=<ur_type> robot_ip:=192.168.56.101 launch_rviz:=true

You can view the polyscope GUI by opening http://192.168.56.101:6080/vnc.html.

When we now move the robot in Polyscope, the robot’s RViz visualization should move accordingly.

For details on the Docker image, please see the more detailed guide here.

Example Commands for Testing the Driver

Allowed UR - Type strings: ur3, ur3e, ur5, ur5e, ur10, ur10e, ur16e, ur20, ur30.

1. Start hardware, simulator or mockup

To do test with hardware, use:
```
ros2 launch ur_robot_driver ur_control.launch.py ur_type:=<UR_TYPE> robot_ip:=<IP_OF_THE_ROBOT> launch_rviz:=true
```
For more details check the argument documentation with ros2 launch ur_robot_driver ur_control.launch.py --show-arguments

After starting the launch file start the external_control URCap program from the pendant, as described above.
To do an offline test with URSim check details about it in this section
To use mocked hardware(capability of ros2_control), use use_fake_hardware argument, like:
```
ros2 launch ur_robot_driver ur_control.launch.py ur_type:=ur5e robot_ip:=yyy.yyy.yyy.yyy use_fake_hardware:=true launch_rviz:=true
```
NOTE: Instead of using the global launch file for control stack, there are also prepeared launch files for each type of UR robots named. They accept the same arguments are the global one and are used by:
```
ros2 launch ur_robot_driver <ur_type>.launch.py
```

2. Sending commands to controllers

Before running any commands, first check the controllers’ state using ros2 control list_controllers.

Send some goal to the Joint Trajectory Controller by using a demo node from ros2_control_demos package by starting the following command in another terminal:
```
ros2 launch ur_robot_driver test_scaled_joint_trajectory_controller.launch.py
```
After a few seconds the robot should move.

To test another controller, simply define it using initial_joint_controller argument, for example when using fake hardware:

ros2 launch ur_robot_driver ur_control.launch.py ur_type:=ur5e robot_ip:=yyy.yyy.yyy.yyy initial_joint_controller:=joint_trajectory_controller use_fake_hardware:=true launch_rviz:=true

And send the command using demo node:

ros2 launch ur_robot_driver test_joint_trajectory_controller.launch.py

After a few seconds the robot should move(or jump when using emulation).

3. Using only robot description

If you just want to test description of the UR robots, e.g., after changes you can use the following command:

ros2 launch ur_description view_ur.launch.py ur_type:=ur5e

Using MoveIt

MoveIt! support is built-in into this driver already.

Real robot / URSim

To test the driver with the example MoveIt-setup, first start the driver as described above.

ros2 launch ur_moveit_config ur_moveit.launch.py ur_type:=ur5e launch_rviz:=true

Now you should be able to use the MoveIt Plugin in rviz2 to plan and execute trajectories with the robot as explained here.

Note

The MoveIt configuration provided here has Trajectory Execution Monitoring (TEM) disabled, as the Scaled Joint Trajectory Controller may cause trajectories to be executed at a lower velocity than they were originally planned by MoveIt. MoveIt’s TEM however is not aware of this deliberate slow-down due to scaling and will in most cases unnecessarily (and unexpectedly) abort goals.

Until this incompatibility is resolved, the default value for execution_duration_monitoring is set to false. Users who wish to temporarily (re)enable TEM at runtime (for use with other, non-scaling controllers) can do so using the ROS 2 parameter services supported by MoveIt.

Fake hardware on ROS2 Galactic

Currently, the scaled_joint_trajectory_controller does not work on ROS2 Galactic. There is an upstream Merge-Request pending to fix that. Until this is merged and released, please change the default controller in the controllers.yaml file. Make sure that the default field is assigned true for the joint_trajectory_controller and false for the scaled_joint_trajectory_controller.

controller_names:
  - scaled_joint_trajectory_controller
  - joint_trajectory_controller


scaled_joint_trajectory_controller:
  action_ns: follow_joint_trajectory
  type: FollowJointTrajectory
  default: false
  joints:
    - shoulder_pan_joint
    - shoulder_lift_joint
    - elbow_joint
    - wrist_1_joint
    - wrist_2_joint
    - wrist_3_joint


joint_trajectory_controller:
  action_ns: follow_joint_trajectory
  type: FollowJointTrajectory
  default: true
  joints:
    - shoulder_pan_joint
    - shoulder_lift_joint
    - elbow_joint
    - wrist_1_joint
    - wrist_2_joint
    - wrist_3_joint

Then start

ros2 launch ur_robot_driver ur_control.launch.py ur_type:=ur5e robot_ip:=yyy.yyy.yyy.yyy use_fake_hardware:=true launch_rviz:=false initial_joint_controller:=joint_trajectory_controller
# and in another shell
ros2 launch ur_moveit_config ur_moveit.launch.py ur_type:=ur5e launch_rviz:=true

Custom URScript commands

The driver’s package contains a urscript_interface node that allows sending URScript snippets directly to the robot. It gets started in the driver’s launchfiles by default. To use it, simply publish a message to its interface:

# simple popup
ros2 topic pub /urscript_interface/script_command std_msgs/msg/String '{data: popup("hello")}' --once

Be aware, that running a program on this interface (meaning publishing script code to that interface) stops any running program on the robot. Thus, the motion-interpreting program that is started by the driver gets stopped and has to be restarted again. Depending whether you use headless mode or not, you’ll have to call the resend_program service or press the play button on the teach panel to start the external_control program again.

Note

Currently, there is no feedback on the code’s correctness. If the code sent to the robot is incorrect, it will silently not get executed. Make sure that you send valid URScript code!

Multi-line programs

When you want to define multi-line programs, make sure to check that newlines are correctly interpreted from your message. For this purpose the driver prints the program as it is being sent to the robot. When sending a multi-line program from the command line, you can use an empty line between each statement:

ros2 topic pub --once /urscript_interface/script_command std_msgs/msg/String '{data:
"def my_prog():

  set_digital_out(1, True)

  movej(p[0.2, 0.3, 0.8, 0, 0, 3.14], a=1.2, v=0.25, r=0)

  textmsg(\"motion finished\")

end"}'

Non-interrupting programs

To prevent interrupting the main program, you can send certain commands as secondary programs.

ros2 topic pub --once /urscript_interface/script_command std_msgs/msg/String '{data:
  "sec my_prog():

    textmsg(\"This is a log message\")

  end"}'