Macros | Functions
stm32f30x_i2c.c File Reference

This file provides firmware functions to manage the following functionalities of the Inter-Integrated circuit (I2C): More...

#include "stm32f30x_i2c.h"
#include "stm32f30x_rcc.h"
Include dependency graph for stm32f30x_i2c.c:

Go to the source code of this file.

Macros

#define CR1_CLEAR_MASK   ((uint32_t)0x00CFE0FF) /*<! I2C CR1 clear register Mask */
 
#define CR2_CLEAR_MASK   ((uint32_t)0x07FF7FFF) /*<! I2C CR2 clear register Mask */
 
#define ERROR_IT_MASK   ((uint32_t)0x00003F00) /*<! I2C Error interrupt register Mask */
 
#define TC_IT_MASK   ((uint32_t)0x000000C0) /*<! I2C TC interrupt register Mask */
 
#define TIMING_CLEAR_MASK   ((uint32_t)0xF0FFFFFF) /*<! I2C TIMING clear register Mask */
 

Functions

void I2C_10BitAddressHeaderCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables the I2C 10-bit header only mode with read direction. More...
 
void I2C_10BitAddressingModeCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables the I2C 10-bit addressing mode for the master. More...
 
void I2C_AcknowledgeConfig (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Generates I2C communication Acknowledge. More...
 
void I2C_AutoEndCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables the I2C automatic end mode (stop condition is automatically sent when nbytes data are transferred). More...
 
void I2C_CalculatePEC (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables the PEC value calculation of the transferred bytes. More...
 
void I2C_ClearFlag (I2C_TypeDef *I2Cx, uint32_t I2C_FLAG)
 Clears the I2Cx's pending flags. More...
 
void I2C_ClearITPendingBit (I2C_TypeDef *I2Cx, uint32_t I2C_IT)
 Clears the I2Cx's interrupt pending bits. More...
 
void I2C_ClockTimeoutCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables I2C Clock Timeout (SCL Timeout detection). More...
 
void I2C_Cmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables the specified I2C peripheral. More...
 
void I2C_DeInit (I2C_TypeDef *I2Cx)
 Deinitialize the I2Cx peripheral registers to their default reset values. More...
 
void I2C_DMACmd (I2C_TypeDef *I2Cx, uint32_t I2C_DMAReq, FunctionalState NewState)
 Enables or disables the I2C DMA interface. More...
 
void I2C_DualAddressCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables the specified I2C dual addressing mode. More...
 
void I2C_ExtendedClockTimeoutCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables I2C Extended Clock Timeout (SCL cumulative Timeout detection). More...
 
void I2C_GeneralCallCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables the specified I2C general call feature. More...
 
void I2C_GenerateSTART (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Generates I2Cx communication START condition. More...
 
void I2C_GenerateSTOP (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Generates I2Cx communication STOP condition. More...
 
uint8_t I2C_GetAddressMatched (I2C_TypeDef *I2Cx)
 Returns the I2C slave matched address . More...
 
FlagStatus I2C_GetFlagStatus (I2C_TypeDef *I2Cx, uint32_t I2C_FLAG)
 Checks whether the specified I2C flag is set or not. More...
 
ITStatus I2C_GetITStatus (I2C_TypeDef *I2Cx, uint32_t I2C_IT)
 Checks whether the specified I2C interrupt has occurred or not. More...
 
uint8_t I2C_GetPEC (I2C_TypeDef *I2Cx)
 Returns the PEC value for the specified I2C. More...
 
uint16_t I2C_GetTransferDirection (I2C_TypeDef *I2Cx)
 Returns the I2C slave received request. More...
 
void I2C_IdleClockTimeoutCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables I2C Idle Clock Timeout (Bus idle SCL and SDA high detection). More...
 
void I2C_Init (I2C_TypeDef *I2Cx, I2C_InitTypeDef *I2C_InitStruct)
 Initializes the I2Cx peripheral according to the specified parameters in the I2C_InitStruct. More...
 
void I2C_ITConfig (I2C_TypeDef *I2Cx, uint32_t I2C_IT, FunctionalState NewState)
 Enables or disables the specified I2C interrupts. More...
 
void I2C_MasterRequestConfig (I2C_TypeDef *I2Cx, uint16_t I2C_Direction)
 Configures the type of transfer request for the master. More...
 
void I2C_NumberOfBytesConfig (I2C_TypeDef *I2Cx, uint8_t Number_Bytes)
 Configures the number of bytes to be transmitted/received. More...
 
void I2C_OwnAddress2Config (I2C_TypeDef *I2Cx, uint16_t Address, uint8_t Mask)
 Configures the I2C slave own address 2 and mask. More...
 
void I2C_PECRequestCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables I2C PEC transmission/reception request. More...
 
uint32_t I2C_ReadRegister (I2C_TypeDef *I2Cx, uint8_t I2C_Register)
 Reads the specified I2C register and returns its value. More...
 
uint8_t I2C_ReceiveData (I2C_TypeDef *I2Cx)
 Returns the most recent received data by the I2Cx peripheral. More...
 
void I2C_ReloadCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables the I2C nbytes reload mode. More...
 
void I2C_SendData (I2C_TypeDef *I2Cx, uint8_t Data)
 Sends a data byte through the I2Cx peripheral. More...
 
void I2C_SlaveAddressConfig (I2C_TypeDef *I2Cx, uint16_t Address)
 Configures the slave address to be transmitted after start generation. More...
 
void I2C_SlaveByteControlCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables the I2C slave byte control. More...
 
void I2C_SMBusAlertCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables I2C SMBus alert. More...
 
void I2C_SoftwareResetCmd (I2C_TypeDef *I2Cx)
 Enables or disables the specified I2C software reset. More...
 
void I2C_StopModeCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables I2C wakeup from stop mode. More...
 
void I2C_StretchClockCmd (I2C_TypeDef *I2Cx, FunctionalState NewState)
 Enables or disables the specified I2C Clock stretching. More...
 
void I2C_StructInit (I2C_InitTypeDef *I2C_InitStruct)
 Fills each I2C_InitStruct member with its default value. More...
 
void I2C_TimeoutAConfig (I2C_TypeDef *I2Cx, uint16_t Timeout)
 Configures the I2C Bus Timeout A (SCL Timeout when TIDLE = 0 or Bus idle SCL and SDA high when TIDLE = 1). More...
 
void I2C_TimeoutBConfig (I2C_TypeDef *I2Cx, uint16_t Timeout)
 Configures the I2C Bus Timeout B (SCL cumulative Timeout). More...
 
void I2C_TransferHandling (I2C_TypeDef *I2Cx, uint16_t Address, uint8_t Number_Bytes, uint32_t ReloadEndMode, uint32_t StartStopMode)
 Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). More...
 

Detailed Description

This file provides firmware functions to manage the following functionalities of the Inter-Integrated circuit (I2C):

Author
MCD Application Team
Version
V1.1.1
Date
04-April-2014
  • Initialization and Configuration
  • Communications handling
  • SMBUS management
  • I2C registers management
  • Data transfers management
  • DMA transfers management
  • Interrupts and flags management
============================================================================
                    ##### How to use this driver #####
============================================================================
  [..]
  (#) Enable peripheral clock using RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2Cx, ENABLE)
      function for I2C1 or I2C2.
  (#) Enable SDA, SCL  and SMBA (when used) GPIO clocks using 
      RCC_AHBPeriphClockCmd() function. 
  (#) Peripherals alternate function: 
      (++) Connect the pin to the desired peripherals' Alternate 
           Function (AF) using GPIO_PinAFConfig() function.
      (++) Configure the desired pin in alternate function by:
           GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AF
      (++) Select the type, OpenDrain and speed via 
           GPIO_PuPd, GPIO_OType and GPIO_Speed members
      (++) Call GPIO_Init() function.
  (#) Program the Mode, Timing , Own address, Ack and Acknowledged Address 
      using the I2C_Init() function.
  (#) Optionally you can enable/configure the following parameters without
      re-initialization (i.e there is no need to call again I2C_Init() function):
      (++) Enable the acknowledge feature using I2C_AcknowledgeConfig() function.
      (++) Enable the dual addressing mode using I2C_DualAddressCmd() function.
      (++) Enable the general call using the I2C_GeneralCallCmd() function.
      (++) Enable the clock stretching using I2C_StretchClockCmd() function.
      (++) Enable the PEC Calculation using I2C_CalculatePEC() function.
      (++) For SMBus Mode: 
           (+++) Enable the SMBusAlert pin using I2C_SMBusAlertCmd() function.
  (#) Enable the NVIC and the corresponding interrupt using the function
      I2C_ITConfig() if you need to use interrupt mode.
  (#) When using the DMA mode 
     (++) Configure the DMA using DMA_Init() function.
     (++) Active the needed channel Request using I2C_DMACmd() function.
  (#) Enable the I2C using the I2C_Cmd() function.
  (#) Enable the DMA using the DMA_Cmd() function when using DMA mode in the 
      transfers.
  [..]        
  (@) When using I2C in Fast Mode Plus, SCL and SDA pin 20mA current drive capability
      must be enabled by setting the driving capability control bit in SYSCFG.
Attention

© COPYRIGHT 2014 STMicroelectronics

Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); You may not use this file except in compliance with the License. You may obtain a copy of the License at:

   http://www.st.com/software_license_agreement_liberty_v2

Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.

Definition in file stm32f30x_i2c.c.



rosflight_firmware
Author(s): Daniel Koch , James Jackson
autogenerated on Wed Jul 3 2019 19:59:27