Macros | Functions
stm32f30x_iwdg.c File Reference

This file provides firmware functions to manage the following functionalities of the Independent watchdog (IWDG) peripheral: More...

#include "stm32f30x_iwdg.h"
Include dependency graph for stm32f30x_iwdg.c:

Go to the source code of this file.

Macros

#define KR_KEY_ENABLE   ((uint16_t)0xCCCC)
 
#define KR_KEY_RELOAD   ((uint16_t)0xAAAA)
 

Functions

void IWDG_Enable (void)
 Enables IWDG (write access to IWDG_PR and IWDG_RLR registers disabled). More...
 
FlagStatus IWDG_GetFlagStatus (uint16_t IWDG_FLAG)
 Checks whether the specified IWDG flag is set or not. More...
 
void IWDG_ReloadCounter (void)
 Reloads IWDG counter with value defined in the reload register (write access to IWDG_PR and IWDG_RLR registers disabled). More...
 
void IWDG_SetPrescaler (uint8_t IWDG_Prescaler)
 Sets IWDG Prescaler value. More...
 
void IWDG_SetReload (uint16_t Reload)
 Sets IWDG Reload value. More...
 
void IWDG_SetWindowValue (uint16_t WindowValue)
 Sets the IWDG window value. More...
 
void IWDG_WriteAccessCmd (uint16_t IWDG_WriteAccess)
 Enables or disables write access to IWDG_PR and IWDG_RLR registers. More...
 

Detailed Description

This file provides firmware functions to manage the following functionalities of the Independent watchdog (IWDG) peripheral:

Author
MCD Application Team
Version
V1.1.1
Date
04-April-2014
  • Prescaler and Counter configuration
  • IWDG activation
  • Flag management
===============================================================================
                         ##### IWDG features #####
===============================================================================
   [..] The IWDG can be started by either software or hardware (configurable
        through option byte).
   [..] The IWDG is clocked by its own dedicated low-speed clock (LSI) and
        thus stays active even if the main clock fails.
        Once the IWDG is started, the LSI is forced ON and cannot be disabled
        (LSI cannot be disabled too), and the counter starts counting down from 
        the reset value of 0xFFF. When it reaches the end of count value (0x000)
        a system reset is generated.
        The IWDG counter should be reloaded at regular intervals to prevent
        an MCU reset.
   [..] The IWDG is implemented in the VDD voltage domain that is still functional
        in STOP and STANDBY mode (IWDG reset can wake-up from STANDBY).          
   [..] IWDGRST flag in RCC_CSR register can be used to inform when a IWDG
        reset occurs.
   [..] Min-max timeout value @41KHz (LSI): ~0.1ms / ~25.5s
        The IWDG timeout may vary due to LSI frequency dispersion. STM32F30x
        devices provide the capability to measure the LSI frequency (LSI clock
        connected internally to TIM16 CH1 input capture). The measured value
        can be used to have an IWDG timeout with an acceptable accuracy. 
        For more information, please refer to the STM32F30x Reference manual.

                     ##### How to use this driver #####
===============================================================================
   [..] This driver allows to use IWDG peripheral with either window option enabled
        or disabled. To do so follow one of the two procedures below.
   (#) Window option is enabled:    
       (++) Start the IWDG using IWDG_Enable() function, when the IWDG is used
            in software mode (no need to enable the LSI, it will be enabled
            by hardware).        
       (++) Enable write access to IWDG_PR and IWDG_RLR registers using
            IWDG_WriteAccessCmd(IWDG_WriteAccess_Enable) function.
       (++) Configure the IWDG prescaler using IWDG_SetPrescaler() function.
       (++) Configure the IWDG counter value using IWDG_SetReload() function.
            This value will be loaded in the IWDG counter each time the counter
            is reloaded, then the IWDG will start counting down from this value.
       (++) Wait for the IWDG registers to be updated using IWDG_GetFlagStatus() function.
       (++) Configure the IWDG refresh window using IWDG_SetWindowValue() function.

   (#) Window option is disabled:    
       (++) Enable write access to IWDG_PR and IWDG_RLR registers using
            IWDG_WriteAccessCmd(IWDG_WriteAccess_Enable) function.
       (++) Configure the IWDG prescaler using IWDG_SetPrescaler() function.
       (++) Configure the IWDG counter value using IWDG_SetReload() function.
            This value will be loaded in the IWDG counter each time the counter
            is reloaded, then the IWDG will start counting down from this value.
       (++) Wait for the IWDG registers to be updated using IWDG_GetFlagStatus() function.
       (++) reload the IWDG counter at regular intervals during normal operation 
            to prevent an MCU reset, using IWDG_ReloadCounter() function.
       (++) Start the IWDG using IWDG_Enable() function, when the IWDG is used
            in software mode (no need to enable the LSI, it will be enabled
            by hardware).    
Attention

© COPYRIGHT 2014 STMicroelectronics

Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); You may not use this file except in compliance with the License. You may obtain a copy of the License at:

   http://www.st.com/software_license_agreement_liberty_v2

Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.

Definition in file stm32f30x_iwdg.c.



rosflight_firmware
Author(s): Daniel Koch , James Jackson
autogenerated on Thu Oct 24 2019 03:17:21