Macros | Functions
stm32f30x_dac.c File Reference

This file provides firmware functions to manage the following functionalities of the Digital-to-Analog Converter (DAC) peripheral: More...

#include "stm32f30x_dac.h"
#include "stm32f30x_rcc.h"
Include dependency graph for stm32f30x_dac.c:

Go to the source code of this file.

Macros

#define CR_CLEAR_MASK   ((uint32_t)0x00000FFE)
 
#define DHR12R1_OFFSET   ((uint32_t)0x00000008)
 
#define DHR12R2_OFFSET   ((uint32_t)0x00000014)
 
#define DHR12RD_OFFSET   ((uint32_t)0x00000020)
 
#define DOR_OFFSET   ((uint32_t)0x0000002C)
 
#define DUAL_SWTRIG_RESET   ((uint32_t)0xFFFFFFFC)
 
#define DUAL_SWTRIG_SET   ((uint32_t)0x00000003)
 

Functions

void DAC_ClearFlag (DAC_TypeDef *DACx, uint32_t DAC_Channel, uint32_t DAC_FLAG)
 Clears the DAC channel's pending flags. More...
 
void DAC_ClearITPendingBit (DAC_TypeDef *DACx, uint32_t DAC_Channel, uint32_t DAC_IT)
 Clears the DAC channel's interrupt pending bits. More...
 
void DAC_Cmd (DAC_TypeDef *DACx, uint32_t DAC_Channel, FunctionalState NewState)
 Enables or disables the specified DAC channel. More...
 
void DAC_DeInit (DAC_TypeDef *DACx)
 Deinitializes the DAC peripheral registers to their default reset values. More...
 
void DAC_DMACmd (DAC_TypeDef *DACx, uint32_t DAC_Channel, FunctionalState NewState)
 Enables or disables the specified DAC channel DMA request. When enabled DMA1 is generated when an external trigger (EXTI Line9, TIM2, TIM4, TIM6, TIM7 or TIM9 but not a software trigger) occurs. More...
 
void DAC_DualSoftwareTriggerCmd (DAC_TypeDef *DACx, FunctionalState NewState)
 Enables or disables simultaneously the two DAC channels software triggers. More...
 
uint16_t DAC_GetDataOutputValue (DAC_TypeDef *DACx, uint32_t DAC_Channel)
 Returns the last data output value of the selected DAC channel. More...
 
FlagStatus DAC_GetFlagStatus (DAC_TypeDef *DACx, uint32_t DAC_Channel, uint32_t DAC_FLAG)
 Checks whether the specified DAC flag is set or not. More...
 
ITStatus DAC_GetITStatus (DAC_TypeDef *DACx, uint32_t DAC_Channel, uint32_t DAC_IT)
 Checks whether the specified DAC interrupt has occurred or not. More...
 
void DAC_Init (DAC_TypeDef *DACx, uint32_t DAC_Channel, DAC_InitTypeDef *DAC_InitStruct)
 Initializes the DAC peripheral according to the specified parameters in the DAC_InitStruct. More...
 
void DAC_ITConfig (DAC_TypeDef *DACx, uint32_t DAC_Channel, uint32_t DAC_IT, FunctionalState NewState)
 Enables or disables the specified DAC interrupts. More...
 
void DAC_SetChannel1Data (DAC_TypeDef *DACx, uint32_t DAC_Align, uint16_t Data)
 Set the specified data holding register value for DAC channel1. More...
 
void DAC_SetChannel2Data (DAC_TypeDef *DACx, uint32_t DAC_Align, uint16_t Data)
 Set the specified data holding register value for DAC channel2. More...
 
void DAC_SetDualChannelData (DAC_TypeDef *DACx, uint32_t DAC_Align, uint16_t Data2, uint16_t Data1)
 Set the specified data holding register value for dual channel DAC. More...
 
void DAC_SoftwareTriggerCmd (DAC_TypeDef *DACx, uint32_t DAC_Channel, FunctionalState NewState)
 Enables or disables the selected DAC channel software trigger. More...
 
void DAC_StructInit (DAC_InitTypeDef *DAC_InitStruct)
 Fills each DAC_InitStruct member with its default value. More...
 
void DAC_WaveGenerationCmd (DAC_TypeDef *DACx, uint32_t DAC_Channel, uint32_t DAC_Wave, FunctionalState NewState)
 Enables or disables the selected DAC channel wave generation. More...
 

Detailed Description

This file provides firmware functions to manage the following functionalities of the Digital-to-Analog Converter (DAC) peripheral:

Author
MCD Application Team
Version
V1.1.1
Date
04-April-2014
  • DAC channels configuration: trigger, output buffer, data format
  • DMA management
  • Interrupts and flags management
===============================================================================
                     ##### DAC Peripheral features #####
===============================================================================
   [..] The device integrates two 12-bit Digital Analog Converters that can 
        be used independently or simultaneously (dual mode):
        (#) DAC1 integrates two DAC channels:
            (++) DAC1 channel 1 with DAC1_OUT1 as output
            (++) DAC1 channel 2 with DAC1_OUT2 as output
            (++) The two channels can be used independently or simultaneously (dual mode)
  
        (#) DAC2 integrates only one channel DAC2 channel 1 with DAC2_OUT1 as output 
        
   [..] Digital to Analog conversion can be non-triggered using DAC_Trigger_None
        and DAC_OUT1/DAC_OUT2 is available once writing to DHRx register using 
        DAC_SetChannel1Data()/DAC_SetChannel2Data.
        
   [..] Digital to Analog conversion can be triggered by:
        (#) External event: EXTI Line 9 (any GPIOx_Pin9) using DAC_Trigger_Ext_IT9.
            The used pin (GPIOx_Pin9) must be configured in input mode.
            
        (#) Timers TRGO: TIM2, TIM8/TIM3, TIM4, TIM6, TIM7, and TIM15 
            (DAC_Trigger_T2_TRGO, DAC_Trigger_T4_TRGO...)
            The timer TRGO event should be selected using TIM_SelectOutputTrigger()
            (++) To trigger DAC conversions by TIM3 instead of TIM8 follow
                this sequence:
                (+++) Enable SYSCFG APB clock by calling
                      RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
                (+++) Select DAC_Trigger_T3_TRGO when calling DAC_Init()
                (+++) Remap the DAC trigger from TIM8 to TIM3 by calling
                      SYSCFG_TriggerRemapConfig(SYSCFG_TriggerRemap_DACTIM3, ENABLE)
        (#) Software using DAC_Trigger_Software
        
   [..] Each DAC channel integrates an output buffer that can be used to 
        reduce the output impedance, and to drive external loads directly
        without having to add an external operational amplifier.
        To enable, the output buffer use  
        DAC_InitStructure.DAC_OutputBuffer = DAC_OutputBuffer_Enable;
        
   [..] Refer to the device datasheet for more details about output impedance
        value with and without output buffer.
        
   [..] Both DAC channels can be used to generate:
        (+) Noise wave using DAC_WaveGeneration_Noise
        (+) Triangle wave using DAC_WaveGeneration_Triangle
        
   [..] Wave generation can be disabled using DAC_WaveGeneration_None
   
   [..] The DAC data format can be:
        (+) 8-bit right alignment using DAC_Align_8b_R
        (+) 12-bit left alignment using DAC_Align_12b_L
        (+) 12-bit right alignment using DAC_Align_12b_R
        
   [..] The analog output voltage on each DAC channel pin is determined
        by the following equation: 
        (+) DAC_OUTx = VREF+ * DOR / 4095 with DOR is the Data Output Register. 
        VREF+ is the input voltage reference (refer to the device datasheet)
        e.g. To set DAC_OUT1 to 0.7V, use DAC_SetChannel1Data(DAC_Align_12b_R, 868);
        Assuming that VREF+ = 3.3, DAC_OUT1 = (3.3 * 868) / 4095 = 0.7V
        
   [..] A DMA1 request can be generated when an external trigger (but not
        a software trigger) occurs if DMA1 requests are enabled using
        DAC_DMACmd()
        DMA1 requests are mapped as following:
        (+) DAC channel1 is mapped on DMA1 channel3 which must be already 
            configured
        (+) DAC channel2 is mapped on DMA1 channel4 which must be already 
            configured

                   ##### How to use this driver #####
===============================================================================          
   [..]
        (+) Enable DAC APB1 clock to get write access to DAC registers
            using RCC_APB1PeriphClockCmd(RCC_APB1Periph_DAC, ENABLE)

        (+) Configure DACx_OUTy (DAC1_OUT1: PA4, DAC1_OUT2: PA5, DAC2_OUT1: PA6)
            in analog mode.

        (+) Configure the DAC channel using DAC_Init()

        (+) Enable the DAC channel using DAC_Cmd()
Attention

© COPYRIGHT 2014 STMicroelectronics

Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); You may not use this file except in compliance with the License. You may obtain a copy of the License at:

   http://www.st.com/software_license_agreement_liberty_v2

Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.

Definition in file stm32f30x_dac.c.



rosflight_firmware
Author(s): Daniel Koch , James Jackson
autogenerated on Thu Oct 24 2019 03:17:21