uart1.c

Go to the documentation of this file.

/*

Copyright (c) 2011, Ascending Technologies GmbH
All rights reserved.

Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:

 * Redistributions of source code must retain the above copyright notice,
   this list of conditions and the following disclaimer.
 * Redistributions in binary form must reproduce the above copyright
   notice, this list of conditions and the following disclaimer in the
   documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.

 */

#include "LPC214x.h"
#include "system.h"
#include "main.h"
#include "uart1.h"
#include "irq.h"
#include "hardware.h"
#include "gpsmath.h"
#include "ssp.h"
#include "sdk.h"
#include "ublox.h"

unsigned char packets;
unsigned char DataOutputsPerSecond;
unsigned int uart_cnt;

unsigned char data_requested=0;
extern int ZeroDepth;

unsigned short current_chksum;
unsigned char chksum_to_check=0;
unsigned char chksum_trigger=1;

unsigned char transmission1_running=0;
unsigned char trigger_transmission=0;

volatile unsigned char baudrate1_change=0;

unsigned char send_buffer[16];
unsigned char *tx_buff;
unsigned char UART1_syncstate=0;
unsigned int UART1_rxcount=0;
unsigned char *UART1_rxptr;

unsigned char UART_CalibDoneFlag = 0;

static volatile unsigned char rb_busy=0;

unsigned char startstring[]={'>','*','>'};
unsigned char stopstring[]={'<','#','<'};


void uart1ISR(void) __irq
{
  unsigned char t;
  IENABLE;
  unsigned iir = U1IIR;
  // Handle UART interrupt
  switch ((iir >> 1) & 0x7)
    {
      case 1:
                  // THRE interrupt
                 if (ringbuffer1(RBREAD, &t, 1))
                 {
                   transmission1_running=1;
                   UART1WriteChar(t);
                 }
                 else
                 {
                   transmission1_running=0;
                 }
        break;
      case 2:
        // RX interrupt
            uBloxReceiveHandler(U1RBR);
            break;
      case 3:
        // RLS interrupt
        break;
      case 6:
        // CTI interrupt
        break;
   }
  IDISABLE;
  VICVectAddr = 0;              /* Acknowledge Interrupt */
}





void UART1Initialize(unsigned int baud)
{
  unsigned int divisor = peripheralClockFrequency() / (16 * baud);
//UART1
  U1LCR = 0x83; /* 8 bit, 1 stop bit, no parity, enable DLAB */
  U1DLL = divisor & 0xFF;
  U1DLM = (divisor >> 8) & 0xFF;
  U1LCR &= ~0x80; /* Disable DLAB */
  U1FCR = 1;
}



//Write to UART1
void UART1WriteChar(unsigned char ch)
{
  while ((U1LSR & 0x20) == 0);
  U1THR = ch;
}



unsigned char UART1ReadChar(void)
{
  while ((U1LSR & 0x01) == 0);
  return U1RBR;
}



void UART1_send(unsigned char *buffer, unsigned char length)
{
  unsigned char cnt=0;
  while(length--)
  {
    while (!(U1LSR & 0x20)); //wait until U1THR is empty
    U1THR = buffer[cnt++];
  }
}




void UART1_send_ringbuffer(void)
{
  unsigned char t;
  if(!transmission1_running)
  {
    if(ringbuffer1(RBREAD, &t, 1))
    {
      transmission1_running=1;
      UART1WriteChar(t);
    }
  }
}

int ringbuffer1(unsigned char rw, unsigned char *data, unsigned int count)      //returns 1 when write/read was successful, 0 elsewise
{
    static volatile unsigned char buffer[RINGBUFFERSIZE];
//      static volatile unsigned int pfirst=0, plast=0; //Pointers to first and last to read byte
        static volatile unsigned int read_pointer, write_pointer;
        static volatile unsigned int content=0;
        unsigned int p=0;
    unsigned int p2=0;

        if(rw==RBWRITE)
        {
                if(count<RINGBUFFERSIZE-content)        //enough space in buffer?
                {
                        while(p<count)
                        {
                                buffer[write_pointer++]=data[p++];
                        }
            content+=count;
            return(1);
                }
        }
        else if(rw==RBREAD)
        {
                if(content>=count)
                {
                        while(p2<count)
                        {
                                data[p2++]=buffer[read_pointer++];
                        }
            content-=count;
            if(!content) //buffer empty
            {
                write_pointer=0;
                read_pointer=0;
            }
                        return(1);
                }
        }
        else if(rw==RBFREE)
        {
          if(content) return 0;
          else return(RINGBUFFERSIZE-11);
        }

        return(0);
}