This file contains all the functions prototypes for the USART firmware library. More...
#include "stm32f10x.h"
Include dependency graph for stm32f10x_usart.h:
This graph shows which files directly or indirectly include this file:
Go to the source code of this file.
Classes | |
| struct | USART_ClockInitTypeDef |
| USART Clock Init Structure definition. More... | |
| struct | USART_InitTypeDef |
| USART Init Structure definition. More... | |
Macros | |
| #define | IS_USART_1234_PERIPH(PERIPH) |
| #define | IS_USART_123_PERIPH(PERIPH) |
| #define | IS_USART_ADDRESS(ADDRESS) ((ADDRESS) <= 0xF) |
| #define | IS_USART_ALL_PERIPH(PERIPH) |
| #define | IS_USART_BAUDRATE(BAUDRATE) (((BAUDRATE) > 0) && ((BAUDRATE) < 0x0044AA21)) |
| #define | IS_USART_CLEAR_FLAG(FLAG) ((((FLAG) & (uint16_t)0xFC9F) == 0x00) && ((FLAG) != (uint16_t)0x00)) |
| #define | IS_USART_CLEAR_IT(IT) |
| #define | IS_USART_CLOCK(CLOCK) |
| #define | IS_USART_CONFIG_IT(IT) |
| #define | IS_USART_CPHA(CPHA) (((CPHA) == USART_CPHA_1Edge) || ((CPHA) == USART_CPHA_2Edge)) |
| #define | IS_USART_CPOL(CPOL) (((CPOL) == USART_CPOL_Low) || ((CPOL) == USART_CPOL_High)) |
| #define | IS_USART_DATA(DATA) ((DATA) <= 0x1FF) |
| #define | IS_USART_DMAREQ(DMAREQ) ((((DMAREQ) & (uint16_t)0xFF3F) == 0x00) && ((DMAREQ) != (uint16_t)0x00)) |
| #define | IS_USART_FLAG(FLAG) |
| #define | IS_USART_GET_IT(IT) |
| #define | IS_USART_HARDWARE_FLOW_CONTROL(CONTROL) |
| #define | IS_USART_IRDA_MODE(MODE) |
| #define | IS_USART_LASTBIT(LASTBIT) |
| #define | IS_USART_LIN_BREAK_DETECT_LENGTH(LENGTH) |
| #define | IS_USART_MODE(MODE) ((((MODE) & (uint16_t)0xFFF3) == 0x00) && ((MODE) != (uint16_t)0x00)) |
| #define | IS_USART_PARITY(PARITY) |
| #define | IS_USART_PERIPH_FLAG(PERIPH, USART_FLAG) |
| #define | IS_USART_STOPBITS(STOPBITS) |
| #define | IS_USART_WAKEUP(WAKEUP) |
| #define | IS_USART_WORD_LENGTH(LENGTH) |
| #define | USART_Clock_Disable ((uint16_t)0x0000) |
| #define | USART_Clock_Enable ((uint16_t)0x0800) |
| #define | USART_CPHA_1Edge ((uint16_t)0x0000) |
| #define | USART_CPHA_2Edge ((uint16_t)0x0200) |
| #define | USART_CPOL_High ((uint16_t)0x0400) |
| #define | USART_CPOL_Low ((uint16_t)0x0000) |
| #define | USART_DMAReq_Rx ((uint16_t)0x0040) |
| #define | USART_DMAReq_Tx ((uint16_t)0x0080) |
| #define | USART_FLAG_CTS ((uint16_t)0x0200) |
| #define | USART_FLAG_FE ((uint16_t)0x0002) |
| #define | USART_FLAG_IDLE ((uint16_t)0x0010) |
| #define | USART_FLAG_LBD ((uint16_t)0x0100) |
| #define | USART_FLAG_NE ((uint16_t)0x0004) |
| #define | USART_FLAG_ORE ((uint16_t)0x0008) |
| #define | USART_FLAG_PE ((uint16_t)0x0001) |
| #define | USART_FLAG_RXNE ((uint16_t)0x0020) |
| #define | USART_FLAG_TC ((uint16_t)0x0040) |
| #define | USART_FLAG_TXE ((uint16_t)0x0080) |
| #define | USART_HardwareFlowControl_CTS ((uint16_t)0x0200) |
| #define | USART_HardwareFlowControl_None ((uint16_t)0x0000) |
| #define | USART_HardwareFlowControl_RTS ((uint16_t)0x0100) |
| #define | USART_HardwareFlowControl_RTS_CTS ((uint16_t)0x0300) |
| #define | USART_IrDAMode_LowPower ((uint16_t)0x0004) |
| #define | USART_IrDAMode_Normal ((uint16_t)0x0000) |
| #define | USART_IT_CTS ((uint16_t)0x096A) |
| #define | USART_IT_ERR ((uint16_t)0x0060) |
| #define | USART_IT_FE ((uint16_t)0x0160) |
| #define | USART_IT_IDLE ((uint16_t)0x0424) |
| #define | USART_IT_LBD ((uint16_t)0x0846) |
| #define | USART_IT_NE ((uint16_t)0x0260) |
| #define | USART_IT_ORE ((uint16_t)0x0360) |
| #define | USART_IT_PE ((uint16_t)0x0028) |
| #define | USART_IT_RXNE ((uint16_t)0x0525) |
| #define | USART_IT_TC ((uint16_t)0x0626) |
| #define | USART_IT_TXE ((uint16_t)0x0727) |
| #define | USART_LastBit_Disable ((uint16_t)0x0000) |
| #define | USART_LastBit_Enable ((uint16_t)0x0100) |
| #define | USART_LINBreakDetectLength_10b ((uint16_t)0x0000) |
| #define | USART_LINBreakDetectLength_11b ((uint16_t)0x0020) |
| #define | USART_Mode_Rx ((uint16_t)0x0004) |
| #define | USART_Mode_Tx ((uint16_t)0x0008) |
| #define | USART_Parity_Even ((uint16_t)0x0400) |
| #define | USART_Parity_No ((uint16_t)0x0000) |
| #define | USART_Parity_Odd ((uint16_t)0x0600) |
| #define | USART_StopBits_0_5 ((uint16_t)0x1000) |
| #define | USART_StopBits_1 ((uint16_t)0x0000) |
| #define | USART_StopBits_1_5 ((uint16_t)0x3000) |
| #define | USART_StopBits_2 ((uint16_t)0x2000) |
| #define | USART_WakeUp_AddressMark ((uint16_t)0x0800) |
| #define | USART_WakeUp_IdleLine ((uint16_t)0x0000) |
| #define | USART_WordLength_8b ((uint16_t)0x0000) |
| #define | USART_WordLength_9b ((uint16_t)0x1000) |
Functions | |
| void | USART_ClearFlag (USART_TypeDef *USARTx, uint16_t USART_FLAG) |
| Clears the USARTx's pending flags. More... | |
| void | USART_ClearITPendingBit (USART_TypeDef *USARTx, uint16_t USART_IT) |
| Clears the USARTx's interrupt pending bits. More... | |
| void | USART_ClockInit (USART_TypeDef *USARTx, USART_ClockInitTypeDef *USART_ClockInitStruct) |
| Initializes the USARTx peripheral Clock according to the specified parameters in the USART_ClockInitStruct . More... | |
| void | USART_ClockStructInit (USART_ClockInitTypeDef *USART_ClockInitStruct) |
| Fills each USART_ClockInitStruct member with its default value. More... | |
| void | USART_Cmd (USART_TypeDef *USARTx, FunctionalState NewState) |
| Enables or disables the specified USART peripheral. More... | |
| void | USART_DeInit (USART_TypeDef *USARTx) |
| Deinitializes the USARTx peripheral registers to their default reset values. More... | |
| void | USART_DMACmd (USART_TypeDef *USARTx, uint16_t USART_DMAReq, FunctionalState NewState) |
| Enables or disables the USART's DMA interface. More... | |
| FlagStatus | USART_GetFlagStatus (USART_TypeDef *USARTx, uint16_t USART_FLAG) |
| Checks whether the specified USART flag is set or not. More... | |
| ITStatus | USART_GetITStatus (USART_TypeDef *USARTx, uint16_t USART_IT) |
| Checks whether the specified USART interrupt has occurred or not. More... | |
| void | USART_HalfDuplexCmd (USART_TypeDef *USARTx, FunctionalState NewState) |
| Enables or disables the USART's Half Duplex communication. More... | |
| void | USART_Init (USART_TypeDef *USARTx, USART_InitTypeDef *USART_InitStruct) |
| Initializes the USARTx peripheral according to the specified parameters in the USART_InitStruct . More... | |
| void | USART_IrDACmd (USART_TypeDef *USARTx, FunctionalState NewState) |
| Enables or disables the USART's IrDA interface. More... | |
| void | USART_IrDAConfig (USART_TypeDef *USARTx, uint16_t USART_IrDAMode) |
| Configures the USART's IrDA interface. More... | |
| void | USART_ITConfig (USART_TypeDef *USARTx, uint16_t USART_IT, FunctionalState NewState) |
| Enables or disables the specified USART interrupts. More... | |
| void | USART_LINBreakDetectLengthConfig (USART_TypeDef *USARTx, uint16_t USART_LINBreakDetectLength) |
| Sets the USART LIN Break detection length. More... | |
| void | USART_LINCmd (USART_TypeDef *USARTx, FunctionalState NewState) |
| Enables or disables the USART's LIN mode. More... | |
| void | USART_OneBitMethodCmd (USART_TypeDef *USARTx, FunctionalState NewState) |
| Enables or disables the USART's one bit sampling method. More... | |
| void | USART_OverSampling8Cmd (USART_TypeDef *USARTx, FunctionalState NewState) |
| Enables or disables the USART's 8x oversampling mode. More... | |
| uint16_t | USART_ReceiveData (USART_TypeDef *USARTx) |
| Returns the most recent received data by the USARTx peripheral. More... | |
| void | USART_ReceiverWakeUpCmd (USART_TypeDef *USARTx, FunctionalState NewState) |
| Determines if the USART is in mute mode or not. More... | |
| void | USART_SendBreak (USART_TypeDef *USARTx) |
| Transmits break characters. More... | |
| void | USART_SendData (USART_TypeDef *USARTx, uint16_t Data) |
| Transmits single data through the USARTx peripheral. More... | |
| void | USART_SetAddress (USART_TypeDef *USARTx, uint8_t USART_Address) |
| Sets the address of the USART node. More... | |
| void | USART_SetGuardTime (USART_TypeDef *USARTx, uint8_t USART_GuardTime) |
| Sets the specified USART guard time. More... | |
| void | USART_SetPrescaler (USART_TypeDef *USARTx, uint8_t USART_Prescaler) |
| Sets the system clock prescaler. More... | |
| void | USART_SmartCardCmd (USART_TypeDef *USARTx, FunctionalState NewState) |
| Enables or disables the USART's Smart Card mode. More... | |
| void | USART_SmartCardNACKCmd (USART_TypeDef *USARTx, FunctionalState NewState) |
| Enables or disables NACK transmission. More... | |
| void | USART_StructInit (USART_InitTypeDef *USART_InitStruct) |
| Fills each USART_InitStruct member with its default value. More... | |
| void | USART_WakeUpConfig (USART_TypeDef *USARTx, uint16_t USART_WakeUp) |
| Selects the USART WakeUp method. More... | |
Detailed Description
This file contains all the functions prototypes for the USART firmware library.
- Version
- V3.5.0
- Date
- 11-March-2011
- Attention
THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
© COPYRIGHT 2011 STMicroelectronics
Definition in file stm32f10x_usart.h.