State Estimation Nodes

ekf_localization_node

ekf_localization_node is an implementation of an extended Kalman filter. It uses an omnidirectional motion model to project the state forward in time, and corrects that projected estimate using perceived sensor data.

ukf_localization_node

ukf_localization_node is an implementation of an unscented Kalman filter. It uses a set of carefully selected sigma points to project the state through the same motion model that is used in the EKF, and then uses those projected sigma points to recover the state estimate and covariance. This eliminates the use of Jacobian matrices and makes the filter more stable. However, it is also more computationally taxing than ekf_localization_node.

Parameters

ekf_localization_node and ukf_localization_node share the vast majority of their parameters, as most of the parameters control how data is treated before being fused with the core filters.

The relatively large number of parameters available to the state estimation nodes make launch and configuration files the preferred method for starting any of its nodes. The package contains template launch and configuration files to help get users started.

Parameters Common to ekf_localization_node and ukf_localization_node

Standard Parameters

~frequency

The real-valued frequency, in Hz, at which the filter produces a state estimate.

Note

The filter will not begin computation until it receives at least one message from one of the inputs.

~sensor_timeout

The real-valued period, in seconds, after which we consider any sensor to have timed out. In this event, we carry out a predict cycle on the EKF without correcting it. This parameter can be thought of as the inverse of the minimum frequency at which the filter will generate new output.

~two_d_mode

If your robot is operating in a planar environment and you’re comfortable with ignoring the subtle variations in the ground (as reported by an IMU), then set this to true. It will fuse 0 values for all 3D variables (Z, roll, pitch, and their respective velocities and accelerations). This keeps the covariances for those values from exploding while ensuring that your robot’s state estimate remains affixed to the X-Y plane.

~[frame]

Specific parameters:

• ~map_frame
• ~odom_frame
• ~base_link_frame
• ~world_frame

These parameters define the operating “mode” for robot_localization. REP-105 specifies three principal coordinate frames: map, odom, and base_link. base_link is the coordinate frame that is affixed to the robot. The robot’s position in the odom frame will drift over time, but is accurate in the short term and should be continuous. The map frame, like the odom frame, is a world-fixed coordinate frame, and while it contains the most globally accurate position estimate for your robot, it is subject to discrete jumps, e.g., due to the fusion of GPS data. Here is how to use these parameters:

1. Set the map_frame, odom_frame, and base_link_frame parameters to the appropriate frame names for your system.

Note

If your system does not have a map_frame, just remove it, and make sure world_frame is set to the value of odom_frame.

2. If you are only fusing continuous position data such as wheel encoder odometry, visual odometry, or IMU data, set world_frame to your odom_frame value. This is the default behavior for the state estimation nodes in robot_localization, and the most common use for it.
3. If you are fusing global absolute position data that is subject to discrete jumps (e.g., GPS or position updates from landmark observations) then:

1. Set your world_frame to your map_frame value
2. Make sure something else is generating the odom->base_link transform. This can even be another instance of a robot_localization state estimation node. However, that instance should not fuse the global data.

The default values for map_frame, odom_frame, and base_link_frame are map, odom, and base_link, respectively. The world_frame parameter defaults to the value of odom_frame.

~transform_time_offset

Some packages require that your transforms are future-dated by a small time offset. The value of this parameter will be added to the timestamp of map->odom or odom->base_link transform being generated by the state estimation nodes in robot_localization.

~transform_timeout

The robot_localization package uses tf2‘s lookupTransform method to request transformations. This parameter specifies how long we would like to wait if a transformation is not available yet. Defaults to 0 if not set. The value 0 means we just get us the latest available (see tf2 implementation) transform so we are not blocking the filter. Specifying a non-zero transform_timeout affects the filter’s timing since it waits for a maximum of the transform_timeout for a transform to become available. This directly implies that mostly the specified desired output rate is not met since the filter has to wait for transforms when updating.

~[sensor]

For each sensor, users need to define this parameter based on the message type. For example, if we define one source of Imu messages and two sources of Odometry messages, the configuration would look like this:

<param name="imu0" value="robot/imu/data"/>
<param name="odom0" value="wheel_encoder/odometry"/>
<param name="odom1" value="visual_odometry/odometry"/>

The index for each parameter name is 0-based (e.g., odom0, odom1, etc.) and must be defined sequentially (e.g., do not use pose0 and pose2 if you have not defined pose1). The values for each parameter are the topic name for that sensor.

~[sensor]_config

Specific parameters:

• ~odomN_config
• ~twistN_config
• ~imuN_config
• ~poseN_config

For each of the sensor messages defined above, users must specify what variables of those messages should be fused into the final state estimate. An example odometry configuration might look like this:

<rosparam param="odom0_config">[true,  true,  false,
                                false, false, true,
                                true,  false, false,
                                false, false, true,
                                false, false, false]</rosparam>

The order of the boolean values are \(X, Y, Z, roll, pitch, yaw, \dot{X}, \dot{Y}, \dot{Z}, \dot{roll}, \dot{pitch}, \dot{yaw}, \ddot{X}, \ddot{Y}, \ddot{Z}\). In this example, we are fusing \(X\) and \(Y\) position, \(yaw\), \(\dot{X}\), and \(\dot{yaw}\).

Note

The specification is done in the frame_id of the sensor, not in the world_frame or base_link_frame. Please see the coniguration tutorial for more information.

~[sensor]_queue_size

Specific parameters:

• ~odomN_queue_size
• ~twistN_queue_size
• ~imuN_queue_size
• ~poseN_queue_size

Users can use these parameters to adjust the callback queue sizes for each sensor. This is useful if your frequency parameter value is much lower than your sensor’s frequency, as it allows the filter to incorporate all measurements that arrived in between update cycles.

~[sensor]_differential

Specific parameters:

• ~odomN_differential
• ~imuN_differential
• ~poseN_differential

For each of the sensor messages defined above that contain pose information, users can specify whether the pose variables should be integrated differentially. If a given value is set to true, then for a measurement at time \(t\) from the sensor in question, we first subtract the measurement at time \(t-1\), and convert the resulting value to a velocity. This setting is especially useful if your robot has two sources of absolute pose information, e.g., yaw measurements from odometry and an IMU. In that case, if the variances on the input sources are not configured correctly, these measurements may get out of sync with one another and cause oscillations in the filter, but by integrating one or both of them differentially, we avoid this scenario.

Users should take care when using this parameter for orientation data, as the conversion to velocity means that the covariance for orientation state variables will grow without bound (unless another source of absolute orientation data is being fused). If you simply want all of your pose variables to start at \(0\), then please use the _relative parameter.

Note

If you are fusing GPS information via navsat_transform_node or utm_transform_node, you should make sure that the _differential setting is false.

~[sensor]_relative

Specific parameters:

• ~odomN_relative
• ~imuN_relative
• ~poseN_relative

If this parameter is set to true, then any measurements from this sensor will be fused relative to the first measurement received from that sensor. This is useful if, for example, you want your state estimate to always start at \((0, 0, 0)\) and with \(roll, pitch,\) and \(yaw\) values of \((0, 0, 0)\). It is similar to the _differential parameter, but instead of removing the measurement at time \(t-1\), we always remove the measurement at time \(0\), and the measurement is not converted to a velocity.

~imuN_remove_gravitational_acceleration

If fusing accelerometer data from IMUs, this parameter determines whether or not acceleration due to gravity is removed from the acceleration measurement before fusing it.

Note

This assumes that the IMU that is providing the acceleration data is also producing an absolute orientation. The orientation data is required to correctly remove gravitational acceleration.

~gravitational_acceleration

If imuN_remove_gravitational_acceleration is set to true, then this parameter determines the acceleration in Z due to gravity that will be removed from the IMU’s linear acceleration data. Default is 9.80665 (m/s^2).

~initial_state

Starts the filter with the specified state. The state is given as a 15-D vector of doubles, in the same order as the sensor configurations. For example, to start your robot at a position of \((5.0, 4.0, 3.0)\), a \(yaw\) of \(1.57\), and a linear velocity of \((0.1, 0.2, 0.3)\), you would use:

<rosparam param="initial_state">[5.0,  4.0,  3.0,
                                 0.0,  0.0,  1.57,
                                 0.1,  0.2,  0.3,
                                 0.0,  0.0,  0.0,
                                 0.0,  0.0,  0.0]</rosparam>

~publish_tf

If true, the state estimation node will publish the transform from the frame specified by the world_frame parameter to the frame specified by the base_link_frame parameter. Defaults to true.

~publish_acceleration

If true, the state estimation node will publish the linear acceleration state. Defaults to false.

~print_diagnostics

If true, the state estimation node will publish diagnostic messages to the /diagnostics topic. This is useful for debugging your configuration and sensor data.

Advanced Parameters

~use_control

If true, the state estimation node will listen to the cmd_vel topic for a geometry_msgs/Twist message, and use that to generate an acceleration term. This term is then used in the robot’s state prediction. This is especially useful in situations where even small amounts of lag in convergence for a given state variable cause problems in your application (e.g., LIDAR shifting during rotations). Defaults to false.

Note

The presence and inclusion of linear acceleration data from an IMU will currently “override” the predicted linear acceleration value.

~stamped_control

If true and use_control is also true, looks for a geometry_msgs/TwistStamped message instead of a geometry_msgs/Twist message.

~control_timeout

If use_control is set to true and no control command is received in this amount of time, given in seconds, the control-based acceleration term ceases to be applied.

~control_config

Controls which variables in the cmd_vel message are used in state prediction. The order of the values is \(\dot{X}, \dot{Y}, \dot{Z}, \dot{roll}, \dot{pitch}, \dot{yaw}\). Only used if use_control is set to true.

<rosparam param="control_config">[true,  false, false,
                                  false, false, true]</rosparam>

~acceleration_limits

How rapidly your robot can accelerate for each dimension. Matches the parameter order in control_config. Only used if use_control is set to true.

<rosparam param="acceleration_limits">[1.3, 0.0, 0.0,
                                       0.0, 0.0, 3.2]</rosparam>

~deceleration_limits

How rapidly your robot can decelerate for each dimension. Matches the parameter order in control_config. Only used if use_control is set to true.

~acceleration_gains

If your robot cannot instantaneously reach its acceleration limit, the permitted change can be controlled with these gains. Only used if use_control is set to true.

<rosparam param="acceleration_limits">[0.8, 0.0, 0.0,
                                       0.0, 0.0, 0.9]</rosparam>

~deceleration_gains

If your robot cannot instantaneously reach its deceleration limit, the permitted change can be controlled with these gains. Only used if use_control is set to true.

~smooth_lagged_data

If any of your sensors produce data with timestamps that are older than the most recent filter update (more plainly, if you have a source of lagged sensor data), setting this parameter to true will enable the filter, upon reception of lagged data, to revert to the last state prior to the lagged measurement, then process all measurements until the current time. This is especially useful for measurements that come from nodes that require heavy CPU usage to generate pose estimates (e.g., laser scan matchers), as they are frequently lagged behind the current time.

~history_length

If smooth_lagged_data is set to true, this parameter specifies the number of seconds for which the filter will retain its state and measurement history. This value should be at least as large as the time delta between your lagged measurements and the current time.

~[sensor]_nodelay

Specific parameters:

• ~odomN_nodelay
• ~twistN_nodelay
• ~imuN_nodelay
• ~poseN_nodelay

If true, sets the tcpNoDelay transport hint. There is some evidence that Nagle’s algorithm intereferes with the timely reception of large message types, such as the nav_msgs/Odometry message. Setting this to true for an input disables Nagle’s algorithm for that subscriber. Defaults to false.

~[sensor]_threshold

Specific parameters:

• ~odomN_pose_rejection_threshold
• odomN_twist_rejection_threshold
• poseN_rejection_threshold
• twistN_rejection_threshold
• imuN_pose_rejection_threshold
• imuN_angular_velocity_rejection_threshold
• imuN_linear_acceleration_rejection_threshold

If your data is subject to outliers, use these threshold settings, expressed as Mahalanobis distances, to control how far away from the current vehicle state a sensor measurement is permitted to be. Each defaults to numeric_limits<double>::max() if unspecified.

~debug

Boolean flag that specifies whether or not to run in debug mode. WARNING: setting this to true will generate a massive amount of data. The data is written to the value of the debug_out_file parameter. Defaults to false.

~debug_out_file

If debug is true, the file to which debug output is written.

~process_noise_covariance

The process noise covariance, commonly denoted Q, is used to model uncertainty in the prediction stage of the filtering algorithms. It can be difficult to tune, and has been exposed as a parameter for easier customization. This parameter can be left alone, but you will achieve superior results by tuning it. In general, the larger the value for Q relative to the variance for a given variable in an input message, the faster the filter will converge to the value in the measurement.

~dynamic_process_noise_covariance

If true, will dynamically scale the process_noise_covariance based on the robot’s velocity. This is useful, e.g., when you want your robot’s estimate error covariance to stop growing when the robot is stationary. Defaults to false.

~initial_estimate_covariance

The estimate covariance, commonly denoted P, defines the error in the current state estimate. The parameter allows users to set the initial value for the matrix, which will affect how quickly the filter converges. For example, if users set the value at position \([0, 0]\) to a very small value, e.g., 1e-12, and then attempt to fuse measurements of X position with a high variance value for \(X\), then the filter will be very slow to “trust” those measurements, and the time required for convergence will increase. Again, users should take care with this parameter. When only fusing velocity data (e.g., no absolute pose information), users will likely not want to set the initial covariance values for the absolute pose variables to large numbers. This is because those errors are going to grow without bound (owing to the lack of absolute pose measurements to reduce the error), and starting them with large values will not benefit the state estimate.

~reset_on_time_jump

If set to true and ros::Time::isSimTime() is true, the filter will reset to its uninitialized state when a jump back in time is detected on a topic. This is useful when working with bag data, in that the bag can be restarted without restarting the node.

Node-specific Parameters

The standard and advanced parameters are common to all state estimation nodes in robot_localization. This section details parameters that are unique to their respective state estimation nodes.

ukf_localization_node

The parameters for ukf_localization_node follow the nomenclature of the original paper and wiki article.

• ~alpha - Controls the spread of sigma points. Unless you are familiar with unscented Kalman filters, it’s probably best for this setting to remain at its default value (0.001).
• ~kappa - Also control the spread of sigma points. Unless you are familiar with unscented Kalman filters, it’s probably best for this setting to remain at its default value (0).
• ~beta - Relates to the distribution of the state vector. The default value of 2 implies that the distribution is Gaussian. Like the other parameters, this should remain unchanged unless the user is familiar with unscented Kalman filters.

Published Topics

• odometry/filtered (nav_msgs/Odometry)

Published Transforms

• If the user’s world_frame parameter is set to the value of odom_frame, a transform is published from the frame given by the odom_frame parameter to the frame given by the base_link_frame parameter.
• If the user’s world_frame parameter is set to the value of map_frame, a transform is published from the frame given by the map_frame parameter to the frame given by the odom_frame parameter.

Note

This mode assumes that another node is broadcasting the transform from the frame given by the odom_frame parameter to the frame given by the base_link_frame parameter. This can be another instance of a robot_localization state estimation node.

Services

• set_pose - By issuing a geometry_msgs/PoseWithCovarianceStamped message to the set_pose topic, users can manually set the state of the filter. This is useful for resetting the filter during testing, and allows for interaction with rviz. Alternatively, the state estimation nodes advertise a SetPose service, whose type is robot_localization/SetPose.rejection