ax12.py

Go to the documentation of this file.

#!/usr/bin/env python

# Copyright (c) 2008-2011 Vanadium Labs LLC. 
# All right reserved.
#
# Redistribution and use in source and binary forms, with or without
# modification, are permitted provided that the following conditions are met:
#
#   * Redistributions of source code must retain the above copyright
#     notice, this list of conditions and the following disclaimer.
#   * Redistributions in binary form must reproduce the above copyright
#     notice, this list of conditions and the following disclaimer in the
#     documentation and/or other materials provided with the distribution.
#   * Neither the name of Vanadium Labs LLC nor the names of its 
#     contributors may be used to endorse or promote products derived 
#     from this software without specific prior written permission.
#
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
# ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
# WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
# DISCLAIMED. IN NO EVENT SHALL VANADIUM LABS BE LIABLE FOR ANY DIRECT, INDIRECT,
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
# LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
# OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
# LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
# OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
# ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

# Author: Michael Ferguson

## @file ax12.py Definitions of AX-12 control table.

# Control Table Symbolic Constants - EEPROM AREA
P_MODEL_NUMBER_L = 0
P_MODEL_NUMBER_H = 1
P_VERSION = 2
P_ID = 3
P_BAUD_RATE = 4
P_RETURN_DELAY_TIME = 5
P_CW_ANGLE_LIMIT_L = 6
P_CW_ANGLE_LIMIT_H = 7
P_CCW_ANGLE_LIMIT_L = 8
P_CCW_ANGLE_LIMIT_H = 9
P_SYSTEM_DATA2 = 10
P_LIMIT_TEMPERATURE = 11
P_DOWN_LIMIT_VOLTAGE = 12
P_UP_LIMIT_VOLTAGE = 13
P_MAX_TORQUE_L = 14
P_MAX_TORQUE_H = 15
P_RETURN_LEVEL = 16
P_ALARM_LED = 17
P_ALARM_SHUTDOWN = 18
P_OPERATING_MODE = 19
P_DOWN_CALIBRATION_L = 20
P_DOWN_CALIBRATION_H = 21
P_UP_CALIBRATION_L = 22
P_UP_CALIBRATION_H = 23
# Control Table Symbolic Constants - RAM AREA
P_TORQUE_ENABLE = 24
P_LED = 25
P_CW_COMPLIANCE_MARGIN = 26
P_CCW_COMPLIANCE_MARGIN = 27
P_CW_COMPLIANCE_SLOPE = 28
P_CCW_COMPLIANCE_SLOPE = 29
P_GOAL_POSITION_L = 30
P_GOAL_POSITION_H = 31
P_GOAL_SPEED_L = 32
P_GOAL_SPEED_H = 33
P_TORQUE_LIMIT_L = 34
P_TORQUE_LIMIT_H = 35
P_PRESENT_POSITION_L = 36
P_PRESENT_POSITION_H = 37
P_PRESENT_SPEED_L = 38
P_PRESENT_SPEED_H = 39
P_PRESENT_LOAD_L = 40
P_PRESENT_LOAD_H = 41
P_PRESENT_VOLTAGE = 42
P_PRESENT_TEMPERATURE = 43
P_REGISTERED_INSTRUCTION = 44
P_PAUSE_TIME = 45
P_MOVING = 46
P_LOCK = 47
P_PUNCH_L = 48
P_PUNCH_H = 49

# Status Return Levels
AX_RETURN_NONE = 0
AX_RETURN_READ = 1
AX_RETURN_ALL = 2

# Instruction Set
AX_PING = 1
AX_READ_DATA = 2
AX_WRITE_DATA = 3
AX_REG_WRITE = 4
AX_ACTION = 5
AX_RESET = 6
AX_SYNC_WRITE = 131
AX_SYNC_READ = 132

AX_CONTROL_SETUP = 26
AX_CONTROL_WRITE = 27
AX_CONTROL_STAT = 28

---

arbotix_python
Author(s): Michael Ferguson
autogenerated on Fri Jan 11 09:52:11 2013