$search

_PR2GripperReleaseCommand.py

Go to the documentation of this file.

"""autogenerated by genmsg_py from PR2GripperReleaseCommand.msg. Do not edit."""
import roslib.message
import struct

import pr2_gripper_sensor_msgs.msg

class PR2GripperReleaseCommand(roslib.message.Message):
  _md5sum = "e62b08129864bf301ed0a1335e6158dc"
  _type = "pr2_gripper_sensor_msgs/PR2GripperReleaseCommand"
  _has_header = False #flag to mark the presence of a Header object
  _full_text = """# the event conditions we would like to trigger the robot to release on
PR2GripperEventDetectorCommand event
================================================================================
MSG: pr2_gripper_sensor_msgs/PR2GripperEventDetectorCommand
# state variable that defines what events we would like to trigger on
# Leaving this field blank will result in the robot triggering when 
# anything touches the sides of the finger or an impact is detected
# with the hand/arm.
int8 trigger_conditions
# definitions for our various trigger_conditions values
# trigger on either acceleration contact or finger sensor side impact
int8 FINGER_SIDE_IMPACT_OR_ACC = 0
# tigger once  both slip and acceleration signals occur
int8 SLIP_AND_ACC = 1 
#  trigger on either slip, acceleration, or finger sensor side impact
int8 FINGER_SIDE_IMPACT_OR_SLIP_OR_ACC = 2
# trigger only on slip information
int8 SLIP = 3
# trigger only on acceleration contact information
int8 ACC = 4 


# the amount of acceleration to trigger on (acceleration vector magnitude)
# Units = m/s^2
# The user needs to be concerned here about not setting the trigger too
# low so that is set off by the robot's own motions.
#
# For large rapid motions, say by a motion planner, 5 m/s^2 is a good level
# For small delicate controlled motions this can be set MUCH lower (try 2.0)
#
# NOTE: When moving the gripper joint (opening/closing the grippr)
# the high gearing of the PR2 gripper causes large acceleration vibrations
# which will cause triggering to occur. This is a known drawback of the PR2.
#
# NOTE: Leaving this value blank will result in a 0 m/s^2 trigger. If you
# are using a trigger_conditions value that returns on acceleration contact
# events then it will immediately exceed your trigger and return
float64 acceleration_trigger_magnitude


# the slip detector gain to trigger on (either finger) : try 0.01
# higher values decrease slip sensitivty (to a point)
# lower values increase sensitivity (to a point)
#
# NOTE: Leaving this value blank will result in the most sensitive slip level.
float64 slip_trigger_magnitude
"""
  __slots__ = ['event']
  _slot_types = ['pr2_gripper_sensor_msgs/PR2GripperEventDetectorCommand']

  def __init__(self, *args, **kwds):
    """
    Constructor. Any message fields that are implicitly/explicitly
    set to None will be assigned a default value. The recommend
    use is keyword arguments as this is more robust to future message
    changes.  You cannot mix in-order arguments and keyword arguments.
    
    The available fields are:
       event
    
    @param args: complete set of field values, in .msg order
    @param kwds: use keyword arguments corresponding to message field names
    to set specific fields. 
    """
    if args or kwds:
      super(PR2GripperReleaseCommand, self).__init__(*args, **kwds)
      #message fields cannot be None, assign default values for those that are
      if self.event is None:
        self.event = pr2_gripper_sensor_msgs.msg.PR2GripperEventDetectorCommand()
    else:
      self.event = pr2_gripper_sensor_msgs.msg.PR2GripperEventDetectorCommand()

  def _get_types(self):
    """
    internal API method
    """
    return self._slot_types

  def serialize(self, buff):
    """
    serialize message into buffer
    @param buff: buffer
    @type  buff: StringIO
    """
    try:
      _x = self
      buff.write(_struct_b2d.pack(_x.event.trigger_conditions, _x.event.acceleration_trigger_magnitude, _x.event.slip_trigger_magnitude))
    except struct.error as se: self._check_types(se)
    except TypeError as te: self._check_types(te)

  def deserialize(self, str):
    """
    unpack serialized message in str into this message instance
    @param str: byte array of serialized message
    @type  str: str
    """
    try:
      if self.event is None:
        self.event = pr2_gripper_sensor_msgs.msg.PR2GripperEventDetectorCommand()
      end = 0
      _x = self
      start = end
      end += 17
      (_x.event.trigger_conditions, _x.event.acceleration_trigger_magnitude, _x.event.slip_trigger_magnitude,) = _struct_b2d.unpack(str[start:end])
      return self
    except struct.error as e:
      raise roslib.message.DeserializationError(e) #most likely buffer underfill


  def serialize_numpy(self, buff, numpy):
    """
    serialize message with numpy array types into buffer
    @param buff: buffer
    @type  buff: StringIO
    @param numpy: numpy python module
    @type  numpy module
    """
    try:
      _x = self
      buff.write(_struct_b2d.pack(_x.event.trigger_conditions, _x.event.acceleration_trigger_magnitude, _x.event.slip_trigger_magnitude))
    except struct.error as se: self._check_types(se)
    except TypeError as te: self._check_types(te)

  def deserialize_numpy(self, str, numpy):
    """
    unpack serialized message in str into this message instance using numpy for array types
    @param str: byte array of serialized message
    @type  str: str
    @param numpy: numpy python module
    @type  numpy: module
    """
    try:
      if self.event is None:
        self.event = pr2_gripper_sensor_msgs.msg.PR2GripperEventDetectorCommand()
      end = 0
      _x = self
      start = end
      end += 17
      (_x.event.trigger_conditions, _x.event.acceleration_trigger_magnitude, _x.event.slip_trigger_magnitude,) = _struct_b2d.unpack(str[start:end])
      return self
    except struct.error as e:
      raise roslib.message.DeserializationError(e) #most likely buffer underfill

_struct_I = roslib.message.struct_I
_struct_b2d = struct.Struct("<b2d")

---

pr2_gripper_sensor_msgs
Author(s): Joe Romano
autogenerated on Tue Mar 5 13:07:51 2013